Forum Post: RE: MSP430FR5729: GPIO pin initialization error.
I think you need "PM5CTL0 &= ~LOCKLPM5;" somewhere.
View ArticleForum Post: RE: TMS320F28379D: Watchdog Management
Hi, For CPU2 also you can trigger CPU2 watchdog reset that should reset CPU2 core. But CPU1 WD reset resets the whole device including CPU2 core [quote userid="573787"...
View ArticleForum Post: RE: AM2612: How to obtain debug information using the TI ARM...
[quote userid="613759"...
View ArticleForum Post: RE: TMS320F28388D: ESC DL Status register reflects connection on...
Hi Ben, [quote userid="612913"...
View ArticleForum Post: RE: TMS320F28388D: Single Node EtherCAT Hardware
Hi Abigail, I assume this is your colleagues post below?...
View ArticleForum Post: RE: TMS320F28P650DK: CLA DCL Parameter update on C2000
Hi Sen, Thank you for the great response. I'll move my control task down to a lower CLA number and run the update parameter task in CLATask1
View ArticleForum Post: RE: TMS320F28P650DH: AQCSFRC has no effect when XCMP enabled.
Hi, Yes when using XCMP AQCSFRC does take into effect. Thanks
View ArticleForum Post: RE: TMS320F28388D: ESC DL Status register reflects connection on...
My ESC DL Status reads 0x5617 indicating that the only open port is 0, all others are closed. I enabled an internal pullup on the PHY1_LINK_STATUS pin and that fixed the Port 1 open issue. Now we are...
View ArticleForum Post: RE: TMDSCNCD28379D: DSP board damaged
Hi, Can you take a look at this app note? https://www.ti.com/lit/pdf/spracf0 Thanks, Ben Collier
View ArticleForum Post: RE: TMS320F28384D: Serial Numbering
Hi Mark, The Class-B devices have a truly unique device identifier. Is your customer only using Class-B devices? Best Regards, Ben Collier
View ArticleForum Post: RE: TMS320F28386S: Debugging the NMI on CM core issue
Hi, CMNMIFLG show FLUNCERR bit set ? Can you find the uncorrectable error using the CM_FLASH_ECC_REGS and information below: Also referring other threads on this forum I found this thread -...
View ArticleForum Post: RE: TMS320F2800157: SCI ROM bootloader with JTAGLOCK enabled and...
It is not mandatory to designate memory regions as secure if you want to use JTAGLOCK. JTAGLOCK is enabled independently from the CSM passwords being programmed or not. If you do not configure memory...
View ArticleForum Post: RE: EVM430-F6736: No Enclosure
Hi Erik, Let me double check that we are still shipping with the enclosure, and if we are I'll let you know to do a product return.
View ArticleForum Post: AM263P4-Q1: Sysconfig Warning After Update
Part Number: AM263P4-Q1 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Hi Team, My customer was previously facing the issue where in a multi-core system project, the customer was not able...
View ArticleForum Post: RE: F29H85X-SOM-EVM: Hardware Security Module of F29h85x
Hi Nikhil, Link that i found in TRM (chapter:ROM Code and Peripheral Booting) - https://www.ti.com/lit/pdf/spruj92 Regards, Shashank
View ArticleForum Post: RE: AM2432: Omron NX701 set drive back to init if the drive is...
Hi Team, You have provided the ESC Register space earlier. In addition to that, could you provide the complete ICSS memory dump for the non-working case and working case (when 0x141.bit0 = 1)? I'm...
View ArticleForum Post: RE: MSP430FR2533: Capacitive touch
The code gets stuck at point marked in yellow. I have tried with the optional clock setting defined in the document but the same issue.
View ArticleForum Post: AM263P4-Q1: UNIFLASH showing success, but application is not...
Part Number: AM263P4-Q1 Other Parts Discussed in Thread: UNIFLASH Tool/software: Hi Team, My customer has been using Uniflash to flash their SBL, App, and XIP app. However, they are not able to boot...
View ArticleForum Post: AM263P4-Q1: Unable to Establish Detection for 10BASE-T
Part Number: AM263P4-Q1 Tool/software: Hi Team, My customer is using the LaunchPad and testing the enet_lwip_cpsw sample program provided. In the test_enet.c L.117 EnetApp_initLinkArgs() function,...
View ArticleForum Post: RE: AM263P4-Q1: Enet CPSW Large Pool Packet Size
Thanks Shaunak. Marked as resolved and will reopen a new thread if necessary.
View Article