Forum Post: RE: LP-AM243: LP-AM243 Error -1170 when connecting debugger
Hi Ryuuichi, [quote userid="80765"...
View ArticleForum Post: RE: LP-AM263P: doubts in running aes encryption code
Hi Nikhil, I tried executing the code as you showed in the video, but I'm still facing the same issue. It's getting stuck in a loop somewhere in the code. I'm attaching the video below -check it once....
View ArticleForum Post: RE: MSP430FR2633: CapSense IC Recommendation with Low Power and...
Hi Eason, If possible, could you please schedule a meeting? This will help us explain our requirements more clearly, address our queries, and get your recommendation on the most suitable CapSense...
View ArticleForum Post: RE: RM48L952: RM48L952 HET Timer pin registers are getting corrupted
Please accept friendship request so that we can chat in private chat window!
View ArticleForum Post: RE: MSP430FR6043: Bidirectional Calibration
Hi, I do not understand what you mean by the reverse flow rate accuracy is not proper from this figure. Could you provide more data to show why you think the accuracy is not good on the reverse flow...
View ArticleForum Post: RE: MSP430FR6047: MCU018
Hi, I can set to 8MHz signal sampling frequency with OSR 10 on my EVM430-FR6047 board without issue. Are there any modifications on both the hardware or software side? And you are programmed with...
View ArticleForum Post: LP-MSPM0G3507: I2C Data transmission and Reception
Part Number: LP-MSPM0G3507 Other Parts Discussed in Thread: MSPM0G3507 Tool/software: Hi, Can we transmit data from one I2C port to another I2C port within the same controller? Launchpad which I am...
View ArticleForum Post: TMS320F2800157: Out to Hex conversion
Part Number: TMS320F2800157 Tool/software: Hello, I need to convert the .out to. hex from the CCS IDE. Is there any way to change the setting to change the default file format for flashing?
View ArticleForum Post: RE: MSP430FR6043: Bidirectional Calibration
Hi, We are using the forward flow calibration data for reverse flow also to make it bidirectional. Forward flow calibration data: Range1 Range2 Range3 Minimum VFR 5.08764 143.946 576.406 Slope 1.2803...
View ArticleForum Post: RE: TMS320F280039C: I2C Module SCL Frequency Inquiry
The pull-up resistors is 10kΩ.
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: High interrupt latency
Hi, At 800MHz, 2μs represents approximately 1600 CPU cycles, which accounts for: - Context saving operations - Vector table lookup - Branch to ISR execution - Multiple interrupt controller transitions...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: MCU-PLUS-SDK-AM243X
Hi Martin, [quote userid="566770"...
View ArticleForum Post: RE: EVM430-FR6047: Uniflash load image failed
I can't read the memory, I think it is the win11 system problem, I tried it in Win10 system, everything works well.
View ArticleForum Post: RE: AM263P4-Q1: Same Flash Address Mapped Using RAT
Hi Aswin, Could you also confirm whether this can be done without the Boot Seg IP (and use RAT instead) as per our discussion? Customer is ok with upgrading SBL to 10.2 since they are already...
View ArticleForum Post: TMS320F28379D: TMS320F28379D: DAL-B Safety Use in Aerospace —...
Part Number: TMS320F28379D Tool/software: Hi TI Support Team, I’m currently evaluating the TMS320F28379D for 64 kW BLDC motor control under DO-178C / DAL-B safety requirements. I’d appreciate your...
View ArticleForum Post: RE: AM263P4-Q1: Unable to Establish Detection for 10BASE-T
Hi Mari, Can you please share which PHY is the customer using with AM263Px? Regards, Shaunak
View ArticleForum Post: TMS320F28377S:How to synchronize two DSPs?
Part Number: TMS320F28377S Tool/software: I am trying to synchronize ePWM1 of DSP2 using the SYNC signal from ePWM1 of DSP1 as an EXTSYNCIN. On DSP1, I am using the Output X-BAR function to output...
View ArticleForum Post: RE: MSP430F5529: VID/PID Licensing and WHQL Driver Support for...
Hi Lake, Could you please provide the latest information on the flow of the program for obtaining VID and PID? Also, is there any problem for customers to use it in mass production? Also, TI has...
View ArticleForum Post: TMS320F28379D: PSFB Digital control
Part Number: TMS320F28379D Other Parts Discussed in Thread: UCC28950 , Tool/software: Dear TI Team, I have completed PSFB topology for EV charger using TI UCC28950 Analog ic and working fine Now i...
View ArticleForum Post: MSP430F5529: USB-UART Bridge Speed, Clock Requirements, and...
Part Number: MSP430F5529 Tool/software: Hi, I have several questions regarding the use of the MSP430F5529 as a USB-to-UART bridge based on the application note SLAAE31: The note mentions that the...
View Article