Forum Post: RE: MSPM0G3507: Latency External ADC Trigger to DMA Complete for...
Hi...at the moment I am using the ADC in "anger" with real signals. I really need to input constant voltages into both ADCs to get a proper answer to you. BUT it "looks like", as you have stated, the...
View ArticleForum Post: RE: EK-TM4C1294XL: How to set Static IP Address for TcpEcho...
Hi, Can you show a screenshot of your NDK setting for static IP configuration? Is 192.168.0.11 an unused address on your network? You need to make sure you are using an available address that is not...
View ArticleForum Post: TMS320F2800157: SCI ROM bootloader with JTAGLOCK enabled and...
Part Number: TMS320F2800157 Tool/software: Dear Texas Instruments Support Team, My device needs to be able to perform firmware updates via SCI and I want to use serial_flash_programmer provided in...
View ArticleForum Post: RE: TMS320F28P650SK: Programming Error after zero-boot pin...
Hi Johnny, Do you see this issue only when DCSM is used? Or do you see the same issue with no DCSM settings? Thank you, Luke
View ArticleForum Post: RE: MSPM0G3519: UART RX voltage level interfere issue
Hi Joe, Sorry for late response, stucked with other tasks. I'll test it within this week and feedback to you. B.R. Sal
View ArticleForum Post: RE: MSP430FR2533: Capacitive touch
Hmm..... Ok, I have seen this type of unexplained behavior in the past and appears to be something with the debugger getting triggered on a phantom address. Never have been able to prove it as it hard...
View ArticleForum Post: RE: MSP-GANG: Cannot Open target device MSP430F427 while using...
Hi Fiy, I find below thread, which might be helpful for you:...
View ArticleForum Post: RE: TMS320F280039C: Need help in getting started with C2000
Hi Hirushan, C28x Academy is the best place to get started for anything and everything related to C2000. It is always recommended to use the latest version of the CCSTUDIO IDE and C2000WARE due to...
View ArticleForum Post: RE: AM263P4-Q1: why config both FLASH_BOOTINFO_SECTOR and...
Hi Fan, They both map to same physical flash hardware. But the reason why 0x8008 0000 is alos assigned in sysconfig is that, the boot control configuaration is stored in this address. In the example...
View ArticleForum Post: RE: TMS320LF2407A: Code Security Module
Hi Paul, You must know the password to unlock the device. Thank you, Luke
View ArticleForum Post: MCU-PLUS-SDK-AM263X: Bug Report genimage.py inside of the...
Part Number: MCU-PLUS-SDK-AM263X Other Parts Discussed in Thread: SYSCONFIG Tool/software: When building my project, I run into the following error on the following dependency versions: Dependency...
View ArticleForum Post: RE: TMDSCNCD28P65X: PI assembly code and ADC sampling times
Thanks for the update. Regarding the integrator limits, what was the process for determining those. I see the sensed variables are scaled [-1,1] and setpoint [0,1] in most TI sample codes but for some...
View ArticleForum Post: MSP430FR6047: MCU018
Part Number: MSP430FR6047 Tool/software: Hi, On EVM-MSP430FR6047 when I set Signal sampling frequency = 4 MHz, Over sampling rate = 20 then it works fine and also communicates using USS design center...
View ArticleForum Post: RE: C2000WARE-MOTORCONTROL-SDK: Running the dual-axis motor...
No. You have to make some changes to support the encoder without index, but there is no reference code for this in motor control SDK.
View ArticleForum Post: RE: TMS320F28386S: CM's SSI port issue
Unfortunately, I am working remotely now, and will be at facility whre the device is set within couple of weeks. But I'll try to ask colleagues to connect the analyzer and capture the results. I will...
View ArticleForum Post: RE: TMS320F2800132: Improve power measurment on motor drive
[quote userid="166470" url="~/support/microcontrollers/c2000-microcontrollers-group/c2000/f/c2000-microcontrollers-forum/1528456/tms320f2800132-improve-power-measurment-on-motor-drive"]I think this is...
View ArticleForum Post: RE: TPS546C23: TPS546C23RVFR
Hi Saista, The programmer script that the GUI outputs was attached on previous E2E:...
View ArticleForum Post: RE: TMS320F2812: Followup Reflow Question
Hi Ben, Any feedback on this? Regards, Lawrence
View ArticleForum Post: TMS320F280049C: HRPWM Up-count, deadband module unavailable
Part Number: TMS320F280049C Other Parts Discussed in Thread: TIDM-DC-DC-BUCK Tool/software: Hi Team, I saw in the TRM, the following note: ' However, in our example design TIDM-DC-DC-BUCK, we set up...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM263PX: Request for CAN Communication Sample...
Hey Shaik, Appoligies for missing those screenshots in the previous post. Including here. I am looping in our software expert to provide additional insight into interrupt configuration. The main...
View Article