Forum Post: RE: MSPM0L1306: Modify CTL0 SPI register value
Hi Diego, thanks a lot for your answer, I will do it and let you know.
View ArticleForum Post: RE: AM2612: AM261x ZEJ: Profinet pinout for 2ports using PHY...
Hi Nilabh, I have pinned the AM261...ZEJ so MII, RMII, or RGMII could be used for each PHY connection. There are some pins where I was unable to avoid a clash of functions on the same pins so we may...
View ArticleForum Post: RE: TMS320F28388D: CAN Message objects configuration
Hi, Can you try using the example CAN test cases? I do not see an issue with CAN mailbox configuration with the existing examples. Just wanted to first confirm that the examples do not show the CAM...
View ArticleForum Post: RE: TMS320F280037C: HTOL parameter
Hi Julia, Let me inquire from our reliability team on this. Please allow me a few days to get some answers. Thanks, Joseph
View ArticleForum Post: RE: TMS320F28388D: EMIF getting unexpected data.
Hi Dongdong, How to tried SDK emif_ex3_16bit_sdram_far example with your timing parameters?
View ArticleForum Post: RE: TMS320F28379D: Does ADCINT1 go through CPU when used as a...
Hi Vignesh, I realized I never properly answered your original question. If the ADCINT is set up as a trigger source for a DMA channel, it does not need to go through the CPU. This trigger is...
View ArticleForum Post: RE: TMS320F28069: CCS 20.1.1 Theia how to change the name of a...
Hello, Note that it looks like you are trying to rename an added FOLDER. https://software-dl.ti.com/ccs/esd/documents/users_guide_ccs/ccs_project-management.html#adding-folders It is not possible to...
View ArticleForum Post: RE: LAUNCHXL-F28379D: Red dot with CPU halted in the debug session
Hi Hitesh, What's the value at the 0x0D60 address before and after replacing? Do they both have the same value at that address? Check to see if PieVectTable.EPWM1_INT is the address 0x0D60 and if the...
View ArticleForum Post: RE: LAUNCHXL-F28379D: i want to add the ADC SOC at count = 0 to...
Hello, To add the condition that the ADC samples at counter = 0, you need to configure the ADC to trigger on the EPWM counter zero event. Here's an example of what you can add to your InitEPwm1Example...
View ArticleForum Post: RE: TMS320F2800156-Q1: About 2800156 Clock lost fault issue
Hello, Based on the information provided, it is likely that a product that has been shipped to the client will require an upgrade program to turn off clock monitoring. I looped in software expert to...
View ArticleForum Post: RE: TM4C129ENCPDT: JTAG programming TM4C failed with corrupted...
Thanks a lot for the information, Charles. These three cases are the valid cases that could cause JTAG halt to fail, but I don't think we have a valid image that has those issues listed. I will keep...
View ArticleForum Post: RE: TMS320F28379D: EnDat Clock Issue: No PWM on GPIO6, Code Hangs...
Hello, Thank you for further clarification. Let me loop in relevant experts on EnDat library to better assist you with your inquiry.
View ArticleForum Post: RE: Pre Defined Symbols to build ONLY cla.obj
Hi Prakhar, Thanks for the detailed explanation. What you've proposed should be feasible as long as the function definitions are defined such that they are applicable for respective core that is being...
View ArticleForum Post: RE: TMS320F28377D: Position of the edges generated by the...
Hello Alberto, The Action-Qualifier submodule latches the compare events, generating output signals based on the state of the compare registers at the time of the event. it's essential to note that...
View ArticleForum Post: RE: TMS320F280039C: Questions about the epwm_ex3_synchronization...
Hi Zhen, Thank you for doing additional tests and sharing the results. Have you modified the phase shift values from what is shown in the example? [quote userid="521369"...
View ArticleForum Post: TMS320F28P650DK: USB Peripheral Enters Device Mode by Itself
Part Number: TMS320F28P650DK Other Parts Discussed in Thread: SYSCONFIG , C2000WARE , TMS320F28069 Tool/software: I am attempting to get a USB MSC host application working on prototype hardware. I...
View ArticleForum Post: RE: TMS320F280049C: CCS output format for Uniflash
The compiler ofd2000.exe and hexC2000.exe seems to only support COF builds according to the tiobj2bin.bat file REM text. Yet the post build option string makes *.bin file for EABI but will not boot...
View ArticleForum Post: AM2634: DACOUT calculation formula
Part Number: AM2634 Tool/software: would like to double confirm if the DACOUT calculation formula is correct or not in TRM CMPSS chapter. If it is correct, how to understand the meaning for parameter...
View ArticleForum Post: TMS320F28P650DK: The reason why motor parameter measurement and...
Part Number: TMS320F28P650DK Tool/software: Hello. I'm writing because I have a question. The TI resistance parameter extraction causes an error with the motor meter when extracting the resistance...
View ArticleForum Post: RE: TMDSCNCD28379D: Renaming multi-cpu project
After fourth attempt I was finally able to rename the project. I didn't do anything out of ordinary but it seemed like the steps that CCS was taking to rename and update the project were affected by...
View Article