Forum Post: TMS320F28388D: The contents of the descriptor and data buffer do...
Part Number: TMS320F28388D Other Parts Discussed in Thread: C2000WARE Tool/software: I'm reposting this thread as it may have gotten buried. Hi experts, When processing received data from Ethernet,...
View ArticleForum Post: LP-AM243: EDS ANALOG INPUT FOR ETHERNET/IP HOW TO WRITE 8 ANALOG...
Part Number: LP-AM243 Tool/software: I review your EDS files. Only examples for Digital input and Digital Output. . I am working a projects , using 8 Analog input , using examples program Please help...
View ArticleForum Post: RE: MSP430FR2676: Inquiry About USB to UART Connection with...
Hello Diego Abad, Is the information you provided based on the assumption that the CAPTIVATE-PGMR is being used? My question is based on the assumption that the CAPTIVATE-PGMR is not used. Steps we...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM263PX: MCU-PLUS-SDK-AM263PX
Hey Rapeti, A shared memory definition between R5FSS1_0 and R5FSS1_1 is required in order for the IPC example to build and execute as expected. What is the reasoning for disabling this from the...
View ArticleForum Post: RE: TMS320F28388S: Debug error(C28xx_CPU1: Error: (Error -1044 @...
Hello. Even though I tried all the suggested procedures, it still fails. However, I replaced the PCB and confirmed that it works normally. There is no problem with the power or OSC of the PCB. I don't...
View ArticleForum Post: RE: TMS320F28379D: Unable to observe XCLKOUT signal on GPIO24 via...
Hello Shivani, One thing I noticed from the snapshots provided. You are setting the incorrect value for GPyGMUXn.GPIOz, this should be 0 instead of 1 to enable the XCLKOUT mux option. Can you try...
View ArticleForum Post: RE: TMS320F280039C: Using eCAP Block in HRCAP Mode to Capture...
Hi Ryan Ma, Yes, I can run the example without any problem and thank for your response.
View ArticleForum Post: RE: MCU-PLUS-SDK-AM263X: SBL_QSPI adds calls to HSM functions
Hi, How do I find out what the problem is?
View ArticleForum Post: RE: TMS320F28P659DK-Q1: UART specification (Manchester coding, QPSK)
Hi Ken, On the F28P65x we have both the SCI and the UART module (both using the UART protocol). The below answers are assuming the UART module is being used (however for SCI the answers are similar -...
View ArticleForum Post: RE: TMS320F28377D: What if the SPI host reads more than 16 words...
Yes, just as you said, so I tried the SPI-DMA solution (using DMA to store the data received by SPI), which did solve the problem of SPI receiving length, but I also encountered another problem, which...
View ArticleForum Post: MSPM0G1105: ADC ref voltage for internal temperature trim voltage?
Part Number: MSPM0G1105 Tool/software: hi Expert, from example code below, the ADC Vref is 3.3V. https://dev.ti.com/tirex/explore/node?node=A__AMc1FKI2xb03oOLrEYYLng__MSPM0-SDK__a3PaaoK__LATEST Vtrim...
View ArticleForum Post: RE: LAUNCHXL-F280049C: Reg : C2000 LAUNCHXL-F280049C Evaluation...
Hi, What do you mean by not being detected? What CCS version and JTAG error are you seeing? Please refer to the F28004x LaunchPad User's Guide for details on getting started. Best, Matt
View ArticleForum Post: RE: TMS320F2800137: Max SCI baud rate
Hi Wayne, Yes, that is correct. The maximum SCI baud rate is always LSPCLK / 16, which is maximized if LSPCLK = SYSCLK/1 is set. Best Regards, Delaney
View ArticleForum Post: RE: LP-MSPM0G3519: Classic CAN is not enabled on MCAL...
Hi Kiran, Got it, will feedback tomorrow, have a meeting with MCAL team then. Please help set up email with me: sal-ye@ti.com Then if there any progress, I can help share inside the emai. Thanks! B.R....
View ArticleForum Post: RE: MSP430F6638: MSP430F6638 controller config using JTAG...
Hi Jithin, It looks like you have not install the luanch file. Please refer to below documents: https://www.ti.com/lit/ug/slau647o/slau647o.pdf Chapter 4.2 introduce the setps for using FET430UIF As...
View ArticleForum Post: RE: MSPM0G3107:
Hi Saras, I can't understand your description here. Could you give more details, thanks. B.R. Sal
View ArticleForum Post: RE: TMS320F28P650DH: CLA optimizating of MMOVIZ + MMOVXI
Hi Hang, Can they try turning on compiler optimizations in their project properties (if not already enabled)? Also, what type of structure is ClatoCpuVar? Generally, the CLA compiler isn't optimized...
View ArticleForum Post: RE: MSPM0-SDK: MCAL 0.2.4: undefined preprocessing identifiers
Hi François, Which MCAL version customer used? B.R. Sal
View ArticleForum Post: RE: MSPM0-SDK: MCAL 0.2.4: undefined preprocessing identifiers
Hi François, I see the customer name in the comments, please set up the email to me: sal-ye@ti.com I will loop the relevant expert in the email loop to see any recommendation. B.R. Sal
View ArticleForum Post: RE: MSP430FR5043: Best way to design external amplifier for USS...
Hi, For hoe to use EVM430-FR6043 board for water metering. Please refer to this app note. https://www.ti.com/lit/ug/tidues5a/tidues5a.pdf Best regards, Cash Hao
View Article