Quantcast
Channel: Microcontrollers
Browsing all 217494 articles
Browse latest View live

Forum Post: RE: TMS320F280025C-Q1: How to change F28002x_int33 model...

Hi Al, [quote userid="392761"...

View Article


Forum Post: RE: TMS320F280039: Phase-shift & frequency changing PWM, missing...

Hi Leo, Please allow another day for me to get back to you on your inquiry. Thanks for your patience! Best Regards, Allison

View Article


Forum Post: RE: TMS320F28388D: JTAG flashing with UNIFlash resulting in Error...

Hi Tim, [quote userid="630992"...

View Article

Forum Post: RE: EEPROM emulation using internal flash

Jay, 1. Yes, that is correct. 2. Read/fetch is okay from anywhere that is not the bank being programmed/erased. Best, Alex

View Article

Forum Post: RE: TMS320F28388D: Communication from CM to CPU1 triggers only...

Hi Ozino, thank you for the answer. Since there is no example for the IPC communication from CM to CPU1, I checked the IPC Module — F2838x CM API Guide document where it is stated that " With very few...

View Article


Forum Post: RE: TMS320F28P550SG: SCI communication parity check error

Hi Jianjun, I apologize for the delay. For the receiving F28P55x device, are you using an interrupt-based approach or a polling approach? If the overflow bit is being set, the data in the RX FIFO...

View Article

Forum Post: RE: LAUNCHXL-F28P65X: Intermittent EtherCAT connection failure...

I built and loaded the program using Flash. After turning the power off and on, the EtherCAT program starts immediately, but the EtherCAT state does not change to the Operation state

View Article

Forum Post: AM2434: Layer2 CPSW Example

Part Number: AM2434 Other Parts Discussed in Thread: SYSCONFIG Tool/software: I'm using LP-am24 evm and I got the l2 CPSW example working. I want to go one step further and make port2 work the same as...

View Article


Forum Post: RE: TMS320F28379D: Does ADCINT1 go through CPU when used as a...

Hi Vignesh, Why do you have the ADCINT1 triggering both an interrupt and a DMA transfer? For you configuration to work you will need to make sure the timing of all of these events is very accurate....

View Article


Forum Post: RE: TMS320F28379D: TMS320F28379D

Hi Sameer, The 'board.h' file is the header file generated by Sysconfig. Sysconfig is a tool that allows you to configure device peripherals through a user interface and autogenerates configuration...

View Article

Forum Post: RE: TMS320F280049C: Using DMA for SPI data transfer between SPIA...

Hi Thao, The TXFFIL/RXFFIL is the FIFO level I mentioned before. Having a larger FIFO level won't necessarily increase the rate of data transfer (if you are talking about DMA transfer rate) but rather...

View Article

Forum Post: RE: MSP430FR6043: MSP-TS430PN80C development board

I saw that the msp430fr6043_1pmx. c routine is implemented by directly manipulating registers. Are there any related library functions corresponding to the routine?

View Article

Forum Post: MSP430FR6043: password protected by JTAG/SBW

Part Number: MSP430FR6043 Tool/software: Can using a password protected by JTAG/SBW to burn programs be achieved with only a two-wire SBW? Or must we cooperate with BSL?

View Article


Forum Post: RE: MSPM0L1306: ADC tolerance

hi Diego, Thanks for your suggestion. I will notify customer.

View Article

Forum Post: RE: MCU-PLUS-SDK-AM243X: CSS 20.1.0: How to create a new project...

A quick note on linker command files If you are running other software on ICSSG1 PRU0, note that you should make sure that the linker.cmd files that are used for the PRU0 and PRU1 projects do not...

View Article


Forum Post: TM4C129ENCPDT: JTAG programming TM4C failed with corrupted flash...

Part Number: TM4C129ENCPDT Tool/software: Hello TI team, We have seen JTAG programming TM4C failed with corrupted flash image. We dumped the flash image as below, and there are some ASCII data. We...

View Article

Forum Post: RE: MCU-PLUS-SDK-AM243X: How do we recognize the potential...

Hi Vaibhav, Any update? Thanks, Merril

View Article


Forum Post: RE: LAUNCHXL-F280039C: CanFd bus off

Hi Joseph, This is the information in the ECR register, and the TEC register is almost filled // // Configure the MCAN Module. // MCANConfig(); while(1) { // // Write message to Message RAM. //...

View Article

Forum Post: RE: MSPM0G3507-Q1: The SPI communication cannot read the RXDATA...

[quote userid="571933"...

View Article

Forum Post: RE: MSPM0C1103-Q1: PWM timer (TIMG8 in CCP0) doesn't work when...

You are welcome, Michele.

View Article
Browsing all 217494 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>