Forum Post: RE: MSP430FR6043: Using multiplexer and using at least 2 MSPs...
Hi Adam, thanks for the question! Are you needing these to be done simultaneously, or just one after the other. Using a mux, you will need to consider the channel-to-channel switch time and the...
View ArticleForum Post: RE: TMS320F280037C: Programming DCSM OTP to Standalone boot from...
Luke, When i attempt to trigger a CPU reset in the CCS GUI, I am getting a No Source Available error and it appears to not complete the reset: The OnReset() GEL function is called once a Debug session...
View ArticleForum Post: TMS320F28388D: Error #10008-D Error #10010 when building core 1...
Part Number: TMS320F28388D Tool/software: Hi, I need some help with this strange error. Building core 2 works fine and generates output file but core 1 does not build correctly. Error message attached...
View ArticleForum Post: RE: TMS320F28379D: EPWM sync pass-through operation
Hello, Let me take a look and will let you know shortly.
View ArticleForum Post: RE: TMS320F280049: Projects containing the same files with...
For both builds please send the following: The text (not a screenshot) of the link command, exactly as system sees it, i.e. with all the build variables replaced with their contents Linker command...
View ArticleForum Post: RE: TMS320F28P650DK: ipc initializes the CPU2 program and runs...
HI Rhea, Have you had a chance to confirm this behaviour using the IPC examples provided in C2000Ware? This is not expected behaviour. Please confirm on your end. Regards, Ozino
View ArticleForum Post: RE: C2000-GANG: Question about possibility of downloading the MCU
Hi, Yes the TMS320F280039C device is able to be programmed using C2000-GANG. After downloading the tool, you can set the MCU Type settings with Group as F28xx Piccolo, and device as TMS320F280039C...
View ArticleForum Post: RE: TMS320F28388D: Communication from CM to CPU1 triggers only...
Hi Stanislav, When you say you reversed the direction of communication, what did you end up changing in the application code to do that? Can you summarize your steps. Thanks. Regards, Ozino
View ArticleForum Post: TMS320F280049C: Is it possible to connect either of the SPI port...
Part Number: TMS320F280049C Tool/software: I would like to find a way to route SPIA TX or SPIB TX to GPIO32 pin 37 on a 280049C in the 56-pad VQFP package. I haven't been able to figure out how to do...
View ArticleForum Post: AM263P4-Q1: Error in writing values to L2OCRAM_BANK4 (0x70200000)...
Part Number: AM263P4-Q1 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Hello, I'm trying to use the memory region from 0x7020 0000 to 0x702F FFFF as shared memory. As none of the examples...
View ArticleForum Post: RE: TMS320F28P559SJ-Q1: Edge detection of ePWM for CMPSS
Hello Ryushi, If you want to reset CMPSS on edge changes you could do following steps: 1. Enable CMPSS Ramp generator 2. Generate Sync event from EPWM: Configure SOCA event to happen on PWMA rising...
View ArticleForum Post: RE: TMS320F28P650DH: The upper computer burns the DSP program
Hello, Please refer to this application note for details about performing firmware upgrades for CPU1/2 over SCI on F28P65x. [quote userid="588878"...
View ArticleForum Post: TMS570LC4357: ADC with DMA and no interrupts
Part Number: TMS570LC4357 Other Parts Discussed in Thread: HALCOGEN Tool/software: I am attempting to utilize DMA with the ADC1 of the TMS570LC4357 without any interrupts. My goal is to sample the ADC...
View ArticleForum Post: MSP430G2221: MSP430G2221
Part Number: MSP430G2221 Tool/software: I have a new design requirement that requires a SPI to MDIO converter. Do you have any design examples using the MSP430 processors that implements something...
View ArticleForum Post: EK-TM4C123GXL: Tiva C Series LaunchPad - Access ROM Bootloader...
Part Number: EK-TM4C123GXL Tool/software: I am using the EK-TM4C123GXL REV B board. I am externally powering the device. I connected to the USB ICDI port and flashed with boot_demo_uart_rom...
View ArticleForum Post: RE: EVM430-FR6047: Schematic / EZFET-light understanding
Thanks, that helps! Am I correct about U101, and that we don't need it if we are not using the EZFET_VCCTARGET voltage rail?
View ArticleForum Post: RE: TMS320F28P650DK: Issue of range avoidance settings function
Hi Leo, In testing this Range Avoidance function, I find that I am able to avoid programming as necessary with this option. For erasing, you may need to use erase protection option to avoid erasing...
View ArticleForum Post: RE: EK-TM4C129EXL: USB host with new class uses address 0 for...
Hi Alsiro, Can you clarify a few things? - Have you run the bare-metal HID Keyboard example? The reason I askes is because your original thread was for the TI-RTOS based HID Keyboard. - Are you seeing...
View ArticleForum Post: RE: TMS320F28P559SJ-Q1: Edge detection of ePWM for CMPSS
[quote userid="647737"...
View Article