Forum Post: LP-MSPM0G3507: PA0 PA1 can be used as PWM 5V outputs?
Part Number: LP-MSPM0G3507 Tool/software: Dear TI experts, I know that the PA0 and PA1 have both a 5V open drain, is it possible to combine the PWM capabilities with a 5V max output? Although I have...
View ArticleForum Post: RE: EVM430-FR6047: Inquiry about the EVM and Ultrasonic transducers
Hi Faris, the article I referenced is intended for a clamp-on style USS application, so it wouldn't be directly in contact with the liquid flowing through the pipe. Nevertheless, you should be able to...
View ArticleForum Post: TMS570LS3137: UniFlash v8.8.0 behavior with MCU programming & CRC
Part Number: TMS570LS3137 Other Parts Discussed in Thread: UNIFLASH , Tool/software: Hello there, We need some help on the following experience with discrepancies that we cannot get a hold of. We...
View ArticleForum Post: RE: LP-MSPM0G3507: PA0 PA1 can be used as PWM 5V outputs?
Hi Vanessa, Unfortunately I don't think you cannot use the 5V open drain pins to create a 5V PWM output, but you could potentially use a 5V rail with a 3.3V PWM output controlling a FET to create a...
View ArticleForum Post: AM2634: Is there an example of properly handling a data or...
Part Number: AM2634 Tool/software: I am trying to enable all ECC errors, and I have the MCAN, TCM, and MSSL2 errors somewhat running. Occasionally the example ECC_Test_run_XXXX_XBitInjectTest...
View ArticleForum Post: RE: TMS320F28054M: Understanding the effects of incorrect stator...
[quote userid="629435"...
View ArticleForum Post: RE: TMS320F28379D: LAUNCHXL-F28379D dev kit: Cannot load and run...
Thanks for the response - your steps worked albeit without the two LEDs synced like I expected. I now just need help transcribing this to the uniflash commandline, my goal is to flash to RAM and...
View ArticleForum Post: RE: TMS320F280025C: F280025C
Hi Premkumar, Can you describe the hardware and debug probe you're using? Are you using 2-pin CJTAG or standard 4-pin JTAG? Please verify power rails too. [quote userid="578292"...
View ArticleForum Post: MSP430F5529: P1OUT, P5DIR, P5DS, P3SEL
Part Number: MSP430F5529 Tool/software: Where can I find documentation of these CCS commands, macros, or whatever they call them.
View ArticleForum Post: RE: MSP430F1611: Crystal Fire Up - BCSCTL1.XT2=1
Hi team, Any update here? -Luke
View ArticleForum Post: RE: TMS320F280039C: struct data alignment
[quote userid="488507" url="~/support/microcontrollers/c2000-microcontrollers-group/c2000/f/c2000-microcontrollers-forum/1429546/tms320f280039c-struct-data-alignment/5495385#5495385"]Is there a...
View ArticleForum Post: RE: MSP430FR5957: Mass erase including IPE data using UART BSL
Thanks for your prompt response JD. The conclusion is not what I was expecting, but life is cruel some times. There is yet some piece of information which I do not completely understand. There is a...
View ArticleForum Post: RE: TMS320F280025-Q1: minimum capacitor for power supply
Duplicate post of below. Closing this one. e2e.ti.com/.../tms320f2800157-q1-minimum-capacitor-for-power-supply
View ArticleForum Post: RE: MSP430F5529: P1OUT, P5DIR, P5DS, P3SEL
Discussed in the digital I/O section of the guide: slau208.
View ArticleForum Post: RE: LAUNCHXL-F28P65X: LAUNCHXL-F28P65X - compatibility with...
Hi, All but SDFM should be compatible. You can always jumper wire the signals as needed. Best, Kevin
View ArticleForum Post: RE: LP-MSPM0G3507: PA0 PA1 can be used as PWM 5V outputs?
It worked fine for me with no load. This with the tima_timer_mode_pwm_dead_band example. Default output PA8: Connected to PA0 with default 4.7K I get to 5 V OK, but I guess you need a stiffer...
View ArticleForum Post: RE: LAUNCHXL-F28379D: Issue with Single Motor Control in FCL...
Hi, I'll need to test this myself and identify if there's an issue. I'll try to get back to you later this week, thanks for your patience. Best, Kevin
View ArticleForum Post: RE: MSP430F5529: P1OUT, P5DIR, P5DS, P3SEL
They are simply aliases for the corresponding registers in the MCU.
View ArticleForum Post: RE: MSP430F5529: P1OUT, P5DIR, P5DS, P3SEL
I looked at the documentation and the ports seem to work the same as other microcontrollers. So why are my bits always inverted? For example: #define bit_set(A,B) A |= B // should set bit to a 1 or...
View ArticleForum Post: RE: LAUNCHXL-F280049C: acquisition and control boards would be...
Hi, Sorry for my delayed response. While the P65x device has 6x eQEP modules, it's true that the P65x LaunchPad only has two dedication eQEP connectors. The LaunchPad board has a 5V to 3.3V level...
View Article