Forum Post: TMS570LS3137: TX/RX MibSpi with DMA and long transfer
Part Number: TMS570LS3137 Tool/software: Hello, I am trying to transfer 384 words using the MibSpi and DMA modules. I understand that since the transfer group buffers are only 128 words long, it would...
View ArticleForum Post: RE: MSP432E401Y: Texas Instruments XDS110 USB Debug Probe/CS_DAP_0
Hi, Do you have another board to try? Do you see XDS110 Debug Probe in Windows Device Manager? In CCS, you can open the target configuration. The target configuration should be provided by your...
View ArticleForum Post: RE: AM2432: What is the difference between primary UART boot mode...
Hello Vaibhav, Sorry, I didn't make it clear. This is a bug in our codebase from previous development. It works fine in SPI boot mode, because ROM helps to initialize the SPI interface. When moving to...
View ArticleForum Post: MSPM0L2228: RTC example code
Part Number: MSPM0L2228 Tool/software: Hi Team, Is there are any example code for access RTC registers to read and write values? Thank you Kind regard Staneslouse
View ArticleForum Post: RE: TM4C123GH6PM: Software reset failure with setting PD3 pin as...
[quote userid="275538"...
View ArticleForum Post: RE: TMS320F28386D: ONE-SHOT MODE Configuration for ECAP Module
Hi Esmail, Please refer to this thread regarding CAP1 measurement when doing one shot mode:...
View ArticleForum Post: RE: MSP430FR2433: UART TX interrupt
It sounds like you want to accept the GPS output via the UCA0 Rx side, then echo it to the Backchannel UART (PC terminal) via the UCA0 Tx side. If so, you should put (only) the TXD jumper back on J101.
View ArticleForum Post: TMDSDOCK28379D: create a PWM signal with a period of 250 ns and...
Part Number: TMDSDOCK28379D Tool/software: Hello, I am looking for a solution to configure a PWM1 signal with a period of 250 ns. I want this signal to be active for 100µs and then deactivated for...
View ArticleForum Post: RE: TMS320F28379D: Flash Api and memory usage document
Hi Learneir, This warning is usually because you're trying to use bitfield but the required files for the memory allocation for this bit field support are missing. Are you starting off with a bit...
View ArticleForum Post: RE: TM4C1294NCPDT: Ethernet TCP Communication Lost and Device Hang
Thanks for your clarification. In the future, please describe your problem as clearly as possible like you just did. Your original post has not much information beside the the client is somehow stuck....
View ArticleForum Post: LAUNCHXL-F280039C: Sensorless FOC example code for PMSM
Part Number: LAUNCHXL-F280039C Other Parts Discussed in Thread: CONTROLSUITE , , TIDA-010956 Tool/software: Hello, I am looking to run a PMSM motor using the TIDA-010956 reference design with a...
View ArticleForum Post: RE: TMS320F28P650DK: How the MCAN recovers from a CAN bus off status
Hi Jinlong, When the Init bit ( CCCR.INIT) is cleared by your code, the MCAN module will then wait for 129 occurrences of Bus Idle (129 × 11 consecutive recessive bits) before resuming normal...
View ArticleForum Post: RE: AM2634: AM2634
Actually, I need the memory layout and organization for OCRAM as the application image for the code has been loaded at OCRAM from QSPI.
View ArticleForum Post: RE: MSP430FR5962: After changing the SPI communication mode, the...
Hi expert： Currently my MSP430 SPI module is configured as follows： Currently my TM4C SPI module is configured as follows： TM4C is the host and MSP430 is the slave. Under this configuration, TM4C can...
View ArticleForum Post: RE: TMS320F28388D: Breakpoints jumping different places on the...
Hi Attila, Please follow these instructions: 1. Import the following folder to your CCS workspace. C:\ti\c2000\C2000Ware_5_03_00_00\driverlib\f2838x\driverlib and select this folder. Your folder...
View ArticleForum Post: RE: AM2434: Is FSI available on the reference design "TIDEP-01032" ?
Hi Paula, Thank you for your answers. That's bad...FSI pins are already used for DRV2 PWM. I installed Motor Control SDK, but can't find PinMux SysConfig file. Could you tell us which folder the file...
View ArticleForum Post: RE: AM2434: How to set Interrupt Priority
Hi Paula, Thank you so much for your answers. Could you help to answer the following questions as well ? [quote userid="10509"...
View ArticleForum Post: RE: AM263P4-Q1: PCB Stack up design
Hi Amit, Via-in-pad construction is used on some ICs with a thermal pad (for example, U84, U85, etc) on the AM263Px control card EVM. For the AM263/Px BGA fan-out itself, via-in-pad is not used....
View ArticleForum Post: TMS320F28388D: USB Bootloader options
Part Number: TMS320F28388D Tool/software: Hello, We want to add device firmware update capability to our product based on the TMS320F28388D via USB. We want to be able to update CPU1/CPU2 and CM and...
View ArticleForum Post: RE: AM2432: Power off and power on with Uart connected, jump to...
Hello Zekun Thank you for the query. Customer needs to verify IO compatibility - if the 3.3V used for the logic is same as the IO supply for the IO group referenced by the UART Is customer expecting...
View Article