Forum Post: RE: CCS/TMS320F28377D: I2c interrupt
Hi Meghana I solve the problem but not in clear mode... When I receive a wrong interrupt I behave as it was a not ack and all seems to work. Regards
View ArticleForum Post: RE: TMS320F28069: Motor reverse fail
Hi Sean, Thaks for your help. Yes, we have the following state during the issue : KpSpd = 25 (it is always fixed during the whole flight, is this normal ? Coming from CTRL_getKp(mc_ctrlHandle,...
View ArticleForum Post: RE: CCS/MSP-EXP432E401Y: Is there a simple procedure to use...
Hi Long, do you have further questions regarding this topic? If not, please select "Resolved" for the post that solved your issue so this thread can be closed out. If you have a different question,...
View ArticleForum Post: RE: RTOS/MSP430FR6989: AutoRun: Target not run as the symbol...
Hi Mounika, I had some internal discussion and learned that this is known problem and obviously some answers in the FAQ question exist. It is also not planned to be fixed because not supported anymore....
View ArticleForum Post: RE: TM4C129ENCPDT: ISR for interrupts from two gpio's
hi Bob, can you point to some sample code for the above suggestion. thank you
View ArticleForum Post: RE: TM4C129ENCPDT: ISR for interrupts from two gpio's
hi Bob, can you point to some sample code for the above suggestion. Thank you.
View ArticleForum Post: CCS/TMS320F28069: First event ECAP lost
Part Number: TMS320F28069 Tool/software: Code Composer Studio Hi, I am using the eCAP Peripheral Module with a TMS320F28069 microcontroller for reading the Hall Sensor input signals from a PMSM. In...
View ArticleForum Post: RE: TMS320F28374S: Crc calculation using VCU and interrupt (Code...
Thank you Sira. Yes, I have two separate CRC object, and at the begining I thougth it was enought, but looking at the library source files, it seems that this do not preserve the full context. If my...
View ArticleForum Post: RE: TMS320F28069: ePWM variable and SFO_TI_V6b_FPU library
Thank you for your response. The TRM discusses SFO library shortly but never mentiones the ePWM array. So my final direct question: does it impact the operation of HRPWM is the ePWM array is left...
View ArticleForum Post: RE: CCS/MSP430G2452: Pressing a button turns the whole device off?
Robert, It's hard to debug this without a schematic and knowing the connections. You have the pull enabled correct? So did you measure the signal on your input pin if it is high? If yes please control...
View ArticleForum Post: RE: TMS320F28035: F28035...
Hi Mathew, Still same issue I have attached a screenshot and image of the current setup, please help us further. If possible, we can set up online call and discuss more detailly. Please help us....
View ArticleForum Post: CCS/TMS320F28069: Software Synchronization ECAP peripherals...
Part Number: TMS320F28069 Tool/software: Code Composer Studio Hi, I am using the eCAP Peripheral Module with a TMS320F28069 microcontroller for reading the Hall Sensor input signals from a PMSM. I am...
View ArticleForum Post: RE: DRV8312-69M-KIT: Instaspin - Motor parameters from lab02...
Increasing the USER_MOTOR_FLUX_EST_FREQ_Hz to (100.0) made it run faster, and the result is more consistent, but still changing a bit - from 1 run: Motor RS= 29.37 Ls_q + Ls_d = 9.89152468e-05...
View ArticleForum Post: RE: F28M36H33B2: USB_UART Monitor
Hi Martin I followed your new instructions but it still does not work. Here is what I did: I created the config file in ccs to have a UART connection and to bypass c28. If I now launch this new...
View ArticleForum Post: RE: MSP430F5659: MSP430F5659 NSR Lower on newer model?
Hi Chris, were you able to resolve you problem? If not pls provide the information requested above. If there will be no response I will close this thread by mid of the week.
View ArticleForum Post: RE: RTOS/MSP430F5659: MSP430F5659 USCI - SPI Module Constantly...
Hi Allan, were you albe to resolve your problem and did the inputs above helped you? If not please let us know. If there will be no response I will close this thread by mid the week.
View ArticleForum Post: RE: CCS/MSP-FET: no device attached error with MSP432P401r
Hi Calex, any update on this thread? If there will be no response I will close this thread by mid of this week.
View ArticleForum Post: RE: MSP430FR6989: Getting fatal error assert.h no file or...
[quote user="Stefan Schauer"] (Please visit the site to view this file)Hi, you can copy the assert.h file from the driverlib library into the scr folder of the library. (i have also attached the file)...
View ArticleForum Post: MSP-EXP430FR2433: How to Code in Register Level
Part Number: MSP-EXP430FR2433 Hi, I'm getting started to code MSP-EXP430FR2433 in register level, But I couldn't found the register level description datasheet. Please anyone guide me how to get...
View ArticleForum Post: LAUNCHXL-F28379D: Compatibility with BOOSTXL-SHARP128
Part Number: LAUNCHXL-F28379D Hello, In the BoosterPack Checker, I could find that the BOOSTXL-SHARP96 is compatible with the LAUNCHXL-F28379D . However, on the product page of this booster, it is...
View Article