Forum Post: RE: How to perform CAN receive and UART transmit in a single...
[quote user="Grishma Bhatt"]note:- I have successfully get CAN data only for once or twice,But can't get continuously CAN data.[/quote]Post your code so other can review it and see what possible...
View ArticleForum Post: MSP-TS430PZ100USB debugging tool
Hi,I am planning to use the MSP-TS430PZ100USB target board.I am newbie to the TI so could you please suggest me which debugger tool I can use for flashing and debugging the target board?TI site says...
View ArticleForum Post: RE: Table is located at the wrong place after compile and link
Chris, We are using the F series just for some preproduction brds as they were more readily available. Our production solution is the std F28062. I must say that the speed by which TI have addressed...
View ArticleForum Post: RE: TIVA new Device Descriptors for CCSV5
Based on new install of CCSv5.5.0.00077 and TivaWare 2.0.1.11577, I also got the problem of missing tm4c129xnczad.xml, when compiling the blinky demo.Both the CCS and the TivaWare are fresh downloads....
View ArticleForum Post: RE: Showing on Display 16x02 from Fordata on Tiva C Series Launchpad
Hi Amit,i have found the main problem on why my LCD doesn't display. It mainly the delay timing in the initialization procedure and also procedure itself. After finding a more accurate method of...
View ArticleForum Post: RE: I am very confused about @ # * in addressing mode
Hi,A memory reference operand uses one of several memory addressing modes to refer to a location inmemory. For detailed explanation you can refer to the Chapter 5 of SPRU430E (Please visit the site to...
View ArticleForum Post: RE: MSP430G2553 as motor controller
Have also a look into the TI Motor Drivers Forum, lost of MSP430 examples:http://e2e.ti.com/support/applications/motor_drivers/default.aspx
View ArticleForum Post: RE: HV Motor control + PFC development kit problems
Hi Richard,Three questions:1) In device manager do you see an entry for TI XDS100 Channel A/B under "Universal Serial Bus controllers"?2) What is your Code Composer Studio target configuration consist...
View ArticleForum Post: RE: Main Oscillator Verification Circuit LM4F
[quote user="Mikhail Mushkatblat"] just wanted to save everybody a bit of time by asking here....[/quote]Should this (lone) reporter qualify (somewhat) as "everybody" - then indeed, "Crazy-making has...
View ArticleForum Post: MSP430F5328 Custom BSL loading from CCS blows JTAG fuse
I am currently trying to develop a custom BSL application for the msp430f5328 processor and have blown 3 security fuses trying to get it to load onto the chip.I currently am just trying to get stubs in...
View ArticleForum Post: Does MINITGCR based Initialization with Parity/ECC enabled can...
Hello Support,When I perform MINITGCR based Memory Hardware Initialization for any RAM group with respective ECC or Parity enabled, if there is a corresponding RAM cell error, will there be respective...
View ArticleForum Post: RM48 HDK silkscreen typo
Hi everyoneI'm using the RM48 HDK and I think there's a typo on the silkscreen - has anyone else run into this issue? On J9 pin 7, the schematic and user guide say it should be connected directly to...
View ArticleForum Post: RE: TPS65381 Watchdog Startup Issue with RM48
So now that I can go active and feed the watchdog reliably, the next problem is that when I attempt to attach a JTAG device for debugging or flashing, the JTAG debugger does a soft reset on the MCU....
View ArticleForum Post: RE: Error connecting to target
I did end up figuring this out. the tutorial is terrible when it comes to installing drivers. there is 3 different drivers a virtual serial port, and 2 ICDI drivers. the answer for the ICDI drivers is...
View ArticleForum Post: TMS570LS1224 in HalCoGen?
Hi;After playing around in HalCoGen 03.06.00 with the TMS570LS1227 (for which we have the TMS570 Hercules Development Kit), I was trying to select the TMS570LS1224 which we plan to include in an...
View ArticleForum Post: RE: TM4C123 - Tiva part number is CCS
Something is wrong with the path to the make utility.Did you create this project, or is it one of the TivaWare examples? If it is your project, look how an existing TivaWare project is configured in...
View ArticleForum Post: RE: BSL across I2C
Hey Andy,The MSP430FR5739 has a bootloader in ROM. That family of devices either has a UART or an I2C bootloader. From the data sheet for the MSP430FR5739, the ROM BSL is for the UART interface. If...
View ArticleForum Post: Estimation of worst-case power consumption for MSP430F523x
Hi.I have questions on the worst-case power consumption of MSP430F5237: both high-frequency & low-frequency mode. Question 1: (high-frequency mode) According to “SLAS897 –SEP. 2013”, “page 1/104”...
View ArticleForum Post: RE: Programming and Debugging Facilities for Production Product
Robert,Do you know if this is true for the XDS200? When I connect it to my PC is see two Serial Port entries in the Device ManagerDo you know what the print statement would be? Thanks,Jeff
View Article