Forum Post: RE: TMS570LC4357: Could "bq79718_sample_code_1.4.zip" be run in...
Thank you jagadish In the CMU sample code, there is the read register function that gains the VCELL18_HI parameter. Q1. Is there any reason to get the cell voltage from 18th cell not from 1st cell?...
View ArticleForum Post: RE: TMS320F28035: SCI boot stuck using control card
Hi Matt, The use case would be similar to LFU, or DFU since no "live" features are required. As you said, a customized bootloader is also a solution, actually customer already uses bootlader on some...
View ArticleForum Post: MSPM0G3507: The defined FULL_SCALE_CURRENT_BASE values are not...
Part Number: MSPM0G3507 Other Parts Discussed in Thread: DRV8323 , DRV8316 , DRV8328 Tool/software: Hi there, I am migrating a motor control project from C2000 to MSPM0G. I found the defined values of...
View ArticleForum Post: TMS320F28P650DH: The upper computer TwinCAT cannot scan the slave...
Part Number: TMS320F28P650DH Tool/software: The upper computer TwinCAT cannot scan the slave device. The DSP runs the f28p65x_cpu1_echoback_solution program (SSC generates code and XML file), and...
View ArticleForum Post: LP-MSPM0L1306: (Error -614 @ 0x0) in CCS 20.0.1.4__1.6.1 Windows 11
Part Number: LP-MSPM0L1306 Tool/software: Hi, I did a bad manipulation (I presume) and the LP-MSPM0L1306 EVB is not working since this manipulation. I have another on and this second one is working...
View ArticleForum Post: RE: MSPM0L1306: Use ADC to clear or set GPIO without ISR
Hey Wayne, I didn't actually run an example, but the ADC does seem to have a window comparator mode. The ADC result is compared against the window high and low values at the end of a conversion, and...
View ArticleForum Post: RE: AM2434: Can a multiple R5 core be triggered by the same...
Hi, Can you please elaborate query little bit? From my understanding, It seems that how can I route a interrupt generated from R5F0-0 core to other R5F cores(R5F0-1, R5F1-0, R5F1-1). Is the above...
View ArticleForum Post: RE: MSPM0L1105: Question on MSPM0 lower power optimization guide
Hey Shengyue, Is the device the customer is working with G3507 or L1105? As for the UART, are they disabling the UART when they go to low power mode? From the description, my understanding is that...
View ArticleForum Post: RE: AM2434: Can a multiple R5 core be triggered by the same...
Yes, that's what I mean. For instance, routing a GPIO interrupt or Timer interrupt generated by the R5F0-0 core to other cores (such as R5F0-1, R5F1-0, R5F1-1) to achieve synchronous triggering across...
View ArticleForum Post: RE: MSP430FR2155: After entering low power mode LPM4, the chip...
Hey Leo, I think you may be missing this: // Disable the GPIO power-on default high-impedance mode // to activate previously configured port settings PM5CTL0 &= ~LOCKLPM5; Here is a GPIO interrupt...
View ArticleForum Post: RE: MSP-FET430U64F: MSP430 FET Flash Programmer
Hello, Do you have a programming header somewhere? How are you connecting the MSP-FET? Using a launchpad to program is totally fine, but you should be able to program via SBW with the MSP-FET as well....
View ArticleForum Post: MSPM0G1507: ADC data result is wrong when using DMA with multiple...
Part Number: MSPM0G1507 Other Parts Discussed in Thread: MSPM0G3507 , SYSCONFIG Tool/software: Hi Expert, I use example project "adc12_max_freq_dma_LP_MSPM0G3507_nortos_ticlang" in sdk 2.2.0.5. I...
View ArticleForum Post: RE: TMS320F280039C: Facing issue in Grid Feed with Improve...
Hi Benjamin Thanks for your quick Response and i request you when the expert join office then please support for the same.
View ArticleForum Post: MSPM0G3507: I2C example source code issue
Part Number: MSPM0G3507 Other Parts Discussed in Thread: , MSP430F5529 Tool/software: Hi I am using LP-MSPM0G3507 to interface with EEPROM(24C02). I tried to use...
View ArticleForum Post: TMS320F280039C: always can error at import sample of Mcan or can
Part Number: TMS320F280039C Other Parts Discussed in Thread: C2000WARE , Tool/software: i always send out can error at can_tx or Mcan_tx while import sample at the board, but i still don't know what...
View ArticleForum Post: RE: MSP-FET430U64F: MSP430 FET Flash Programmer
Hello JD, Thank you for your response We are not using any programming headers in the board. But we have a on board pins header with RST, TEST and GND pins. My question is that by connecting only RST,...
View ArticleForum Post: RE: AM2432: Access Main Domain Peripherals from MCU Domain
Hi Kevin, [quote userid="546457"...
View ArticleForum Post: RE: [FAQ] TMS570LC4357: HALCOGEN CSP Unit Test with TAU and LDRA
1. Why does the TCF generation fail? The test sequence is open in Microsoft Excel TCF generation may get stuck if a test case is not terminated by a blank row TCF generation may get stuck if the...
View ArticleForum Post: RE: TMS320F28035: SCI boot stuck using control card
Hi Hang, Thank you for the clarification. You can jump directly to the SCI bootloader in ROM using software, but there are a few things to keep in mind. Note however that the device may be at a...
View ArticleForum Post: RE: TMS570LC4357: How to read the data using UART & Python
Hi JJ, [quote userid="635413"...
View Article