Forum Post: RE: LAUNCHXL-F28379D: Attempt to flash / enter debug session...
Hi Nicole, Apologies for the delay, do you still need assistance with this? Regards, Charles
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: Writing to DDR when ECC is enabled
Hi, Nihar: I have a related question. Is enabling ECC protection for DDR an overkill in applications with high-bandwidth streaming data, such as video at 10 MB/s, where data changes constantly and...
View ArticleForum Post: AM2434: Change RGMII to RMII
Part Number: AM2434 Tool/software: Dear experts, Is there a something like a checklist of the bare minimum of registers that need to be configured to change from RGMII to RMII on CPSW. Regards, Alex
View ArticleForum Post: RE: TMS320F280034: Can not erase FLASH after bootloader
Hi Jiaqi, In customer code PAGE_SIZE is set as 0x1000(bytes in sector), which is input to blank check api as length as below. Since blank check function uses 32bit length, user should provide sector...
View ArticleForum Post: MSP430F5529: Why doesn't while(1); halt the program?
Part Number: MSP430F5529 Tool/software: This is running on the LaunchPad development board, does that have something to do with it? I'm getting strange behavior on my I/O ports when running but with a...
View ArticleForum Post: RE: AM2631: BandGap circuit (BG_RDY) and CFG0 Register settings...
Hey Ralph, Works for me dude! And I've confirmed it is only for testing purposes so honestly, that take the load off in my mind. Any additional input still welcomed, but honestly not that critical....
View ArticleForum Post: RE: TMS320F280039C: SCI (UART) TX at high baudrate not continuous
Hi Gus, I see you got assigned to this thread. So besides SPI you are now also SCI expert Please let me know if you have any questions. If needed, I can also share you the full code. BR, Ben
View ArticleForum Post: RE: TMS320F28377D: The DSP28377D is causing the crystal...
There is no change in the project.As you see, the VDDIO is not exceed 3.3V.Even if the crystal oscillator and capacitor are replaced, the measured waveform peak should not exceed 3.3V. We are in...
View ArticleForum Post: RE: AM2431: accuracy of the MCU_RC_OSC_12M
Hi Paul I found in another forum that the "AM2431: Internal oscillator accuracy" is listed as ±10%. However, the response I received this time says -10% and +10.5%. Which one is correct? Regards,...
View ArticleForum Post: RE: TMS320F28335: Output oscillation problem
HI Luo Thank you for your answer, but there is no code involving motor parameters at level3 and before. At present, I have not tested the SMO module. I am currently testing the SPEED_FR module and PI...
View ArticleForum Post: RE: AM2431: accuracy of the MCU_RC_OSC_12M
II suspect the document that says the limit is ±10% was simply rounded to the nearest whole number. The nominal frequency is 12.55MHz. The upper limit provided in my previous reply represents a...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: MCSPI peripheral mode, how to check...
Hi Jun, yes, that's the way it works. Now I have found a solution: Configure RXFIFO to 2, which can trigger SPI ISR every 2 bytes, so that the received length can be obtained indirectly through...
View ArticleForum Post: RE: TMS320F2800137: no "selected sectors only" erase setting in...
Hi Rajeshwary Is there the update plan to add this function in next version ccs? It is necessary if customer only need to erase some data in “data” sector. thanks joe
View ArticleForum Post: RE: TMS320F28379D: How to have a shared pre-processor in CPU and CLA
Hello, As long as you have included this header file inside of your CLA file, you should be able to reference any defines from the header file inside a CLA task. If you take a look at some of the...
View ArticleForum Post: RE: EVM430-CAPMINI: Firmware binary for CapTivate HID bridge...
You can read the device memory from the JTAG port, using eZ-FET or something else which can debug MSP430, with Uniflash
View ArticleForum Post: RE: TPS55289: Using TMDSCNCD280039C to control TPS55289...
Hi Peng, Since this is related to I2C Example Code regarding with TMDSCNCD280039C, I will assign to the corresponding team. Thanks. BRs, Bryce
View ArticleForum Post: RE: AM2432: SOC writing LPDDR4 timing error
Hi JJD: We have used TI's sysconfig tool to configure LPDDR4,The problem only occurred after using sysconfig to generate a DDR profile for my board,Now I'd like you to help me identify if it's one of...
View ArticleForum Post: RE: TMS320F28377D: CLA Use; structure variable defines; CMD
Hi Shengxiang, I apologize for the delay. What optimization level do you have set in the project? You can check this by right clicking on the project name >> Properties >> Optimization. It...
View ArticleForum Post: RE: TMS320F280039C: Some questions about RAM testing in pbist
Mattherw, Sure, much apperaciate that, wish the best holidays to them!! Regards, Hengchen
View Article