Forum Post: RE: TMS320F28027F: TMS320F28027with DRV8301 to run bldc motor
Hi Jason Osborn // system includes #include #include "main.h" #include "sw/drivers/sci/src/32b/f28x/f2802x/sci.h" #include "hal.h" #include "hal_obj.h" //Added // Define motor control and UART...
View ArticleForum Post: RE: TMS320F28P659DK-Q1: TMS320F28P659DK-Q1
Hi Charles, Thank you for your reply. Today morning I selected a different target configuration e.g. TMS320F28P659 DH8 -Q1, instead of KH8 (on our custom board), and CCS flashed without crashing. I...
View ArticleForum Post: MCU-PLUS-SDK-AM243X: AM243x-LP
Part Number: MCU-PLUS-SDK-AM243X Tool/software: I am switching from TwinCAT to real EtherCAT master. I am trying to connect master to two sitara AM243x-LP boards and I am trying to switching from...
View ArticleForum Post: RE: RM57L843: Atomic variable access support in TI Code composer
Hi Jagadish, Thank for the reply. I am getting "Page not found" when I click on first two links. Thanks, Ravi
View ArticleForum Post: TMS570LS3137: Simulink toolchain
Part Number: TMS570LS3137 Tool/software: Hi, I was wondering if any toolchain was existant to deploy simulink code on a tms570ls3137? Thanks Florent
View ArticleForum Post: RE: TMS570LS3137: Simulink toolchain
Hello Florent, We don't have support for this for TMS570:...
View ArticleForum Post: RE: AM2434: ospi flash
Hi, wenjun.zhang. How can I set the memory mapping attribute to 'strongly ordered'? .tex =0 means strongly ordered. .tex = 1 means shareable device .text = 16 means Non shareable device. Please verify...
View ArticleForum Post: TM4C1294KCPDT: Loading Firmware through UART using LM Flash...
Part Number: TM4C1294KCPDT Other Parts Discussed in Thread: TM4C1294NCPDT Tool/software: Dear Team, We are using TM4C1294KCPDT based customized board for one our application which uses TCP/IP...
View ArticleForum Post: RE: AM2634: How to configure AM2634 in SPI Master and Slave mode...
Please check if the McSPI interrupt i VIM module is enabled, the interrupt number is 78: And if the McSPI TX0 Empty and RX0 full are enabled (McSPI IRQEnable register), and if the interrupt flags are...
View ArticleForum Post: TMDSCNCD263: Incorrect Pinout
Part Number: TMDSCNCD263 Tool/software: Hello, I was looking through the pinout for the HSEC-180 connector and I noticed that pins 133 and 134 have different signals names but the exact same muxed...
View ArticleForum Post: RE: LP-MSPM0L1306: - from hell
"no one is around from the 1980s-2004" I am, and I remember it being a lot worse unless you were buying 50000 of something.
View ArticleForum Post: RE: LP-MSPM0L1306: - from hell
hasn't been that way for me. we used to call and get to a knowledgeable person on second ring. now its just a filter.
View ArticleForum Post: RE: MSPM0L1306: Unlocking via SWD SEC-AP using a password
Hello Vrata, I sent you a friend request on E2E. Once you accept, we can exchange email in private message and I can connect you with Henry. Thanks, JD
View ArticleForum Post: RE: LAUNCHXL-F280039C: universal_motorcontrol_lab_f28003x - Error...
John, For your first question, the FAST algorithm accounts for and requires a hardware voltage filter, implemented by C9, C10, C11. Without those, it will not operate correctly. For the second...
View ArticleForum Post: RE: TMS320F28027F: TMS320F28027with DRV8301 to run bldc motor
Hello, If you're going to add files to your post, please try and add those files as attachments to prevent another situation where the thread causes issues with e2e. In order to help you further with...
View ArticleForum Post: RE: LP-MSPM0C1104: IO expander appnote is missing
Hello Koichiro, I sent you a draft via email. For anyone else who happens to find this thread, the subsystem app note will be published here in the next week or so: https://www.ti.com/lit/slaael9...
View ArticleForum Post: RE: TMS320F2800157: DAC To ADC Loopback Test on TMS320F2800157
Hi Mazen, If you want to have a loopback test on DAC, you simply have to program the DAC registers to output a voltage and convert this voltage through the ADC channels corresponding to the DAC that...
View ArticleForum Post: RE: EK-TM4C1294XL: Parts required for using the LaunchPad...
Thank you once again Charles We've never used JTAG but I guess this may be the way to go. I was intending to use the Micro USB B connector as it easily lets anyone here program the flash without...
View ArticleForum Post: RE: LP-MSPM0L1306: - from hell
Hey Tom, Could you install the latest version of Code Composer Studio or Theia? They contain the drivers that should address the issue you are seeing at the moment. This E2E thread below also contains...
View ArticleForum Post: RE: LP-MSPM0L1306: - from hell
I had already downloaded CCS 1.5 from the TI site.
View Article