Forum Post: RE: SM470R1B1M-HT: Error help needed
im using segger j-link programmer. this is the only board with this issue. we had to replace this component recently.
View ArticleForum Post: RE: TMS570LC4357: Timing for copying virtual sector and erasing a...
Hi Veena, [quote userid="623285"...
View ArticleForum Post: RE: MSP432E401Y: How to manually control ALE in EPI HB16 mode
Hi Monica, You need to use EPIAddressMapSet to specify the base address of a EPI memory as well as the size of the memory. In your oriignal code, you only specify the Peripheral Address Space Size and...
View ArticleForum Post: MSPM0G3507: secondary BSL - change invoke pin/deactivate GPIO...
Part Number: MSPM0G3507 Tool/software: Heyho! I'm working on secondary BSL (secondary_bsl_uart_LP_MSPM0G3507_nortos_ticlang) because I want to change UART-BSL-Pins from default UART0 to UART1. This...
View ArticleForum Post: RE: SM470R1B1M-HT: Error help needed
Hi Rich, I'm not exactly sure what is the cause of the problem. It seems like J-link is unable to connect to the device through the JTAG interface. You said you are trying to replace this component....
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: SysConfig 12.1 creates incorrect MCSPI...
Hi Steve, There is a whole bunch of information provided. Can you just clarify me what SDK + SysCOnfig version creates wrong parameters in ti_drivers_config.c ? Regards, Vaibhav
View ArticleForum Post: RE: SM470R1B1M-HT: Error help needed
we have replaced the SM470R1B1 chip, now we get this error. is there something need to be done before installing a new one?
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: MCSPI: how can I read if the D1 input...
Hi Steve, Thank you very much for your patience. [quote userid="317967"...
View ArticleForum Post: RE: TMS320F2800156-Q1: ADC measurements erratic - measuring...
VREFHI needs to have an external cap for the internal reference buffer. You need to have a 2.2uF connected from VREFHI to VREFLO (GND). Best regards, Joseph
View ArticleForum Post: RE: BOOSTXL-K350QVG-S1: MSP430F5529LP or MSP-EXP432E401Y
Thanks for your rapid response Keith I did use the example in the MSP-GRLIB for the MSP430F5529LP. The touch seems to work fine as it interrupts at the correct place, but nothing displays on the LCD....
View ArticleForum Post: RE: SM470R1B1M-HT: Error help needed
You might want to check the solder flux and make sure you have solid connection on the JTAG interface for nTRST, TMS, TCK, TDI, TDO. I hate to suggest replacing another chip yet but that may be a...
View ArticleForum Post: TMS570LS0432: Data Abort Exception on Software Reset with FreeRTOS
Part Number: TMS570LS0432 Other Parts Discussed in Thread: HALCOGEN Tool/software: Hi everyone, I'm encountering a data abort exception when attempting a software reset in my project using the...
View ArticleForum Post: RE: MSPM0G3507: secondary BSL - change invoke pin/deactivate GPIO...
And isn't this code in boot_config.c (Lines 80-83): . interfacePins . UART_RXD_pad_num = DEF_UART_RXD_PAD, . interfacePins . UART_RXD_PF_mux_sel = DEF_UART_RXD_MUX, . interfacePins . UART_TXD_pad_num...
View ArticleForum Post: RE: TM4C1290NCPDT: Compiling Library with compiler 6 of Arm
Hi, I'm not familiar with the Keil toolchain and don't know the compatibility difference between compiler 5 and 6. I will suggest you contact Keil and see if there is any compiler switches you can...
View ArticleForum Post: RE: TMS320F28388D: UDP Frame over EtherCAT
Hello, The EtherCAT expert will get back to you with a response in the next 1-2 days. Best Regards, Delaney
View ArticleForum Post: RE: TMS320F280025C: Can PMBus be both master and slave at the...
Hi, Aishwarya: I have an power supply need to play master role and control other units when there is no system connect to my power supplies, and when there is a system connect to my power units, I...
View ArticleForum Post: RE: LAUNCHXL-F28P55X: SCIA not working beyond baud rate of...
Hi Ganesh, Are you using a COM port to test different baud rates (using the UART-to-USB bridge on the LaunchPAD) or are you testing via the SCIA pins (device-to-device communication)? If you are doing...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM273X: AM273 GPIO
hello Erilk, I already resolved this issue, the configration is correct, but the GPIO number should be set to GPIO 27 for RCSS_GPIO. The GPIO is still K15 (GPIO59), why it should be set to RCSS GPIO...
View ArticleForum Post: C2000WARE: The Interrelationship between Digital Power SDK and CLB
Part Number: C2000WARE Tool/software: Hi all, We are starting to design the high power and efficiency AC/DC + DC/DC Power Converter. It consist of type-T PFC + LLC topology. We want to i ncorporate...
View Article