Forum Post: TMS570LS3137: EMAC_BUF_DESC_EOQ and TXHDP0 bit blocked
Part Number: TMS570LS3137 Hi it seems in particular bad luck situations, the estif_transmit function remain looped forever finding EMAC_BUF_DESC_EOQ and TXHDP0 .... I'm speaking about this static void...
View ArticleForum Post: RE: TMS320F280025C: Motor control SDK general project and...
Hi Yara, After receiving your positive reply, I increased the voltage to 24v to drive the 24v motor. But it can't start the motor properly. My operation is as follows: I load the general motor control...
View ArticleForum Post: RE: MSP430FR6047: How to get ADC data(waveform) in the...
Hi, You should directly use the data. There is no idx saved in the memory. A sound path of 1m. Emm, it is hard to support by the MSP430FR6047. Due to the limitation of ADC RAM size. The ADC capture...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: FORWARD_MODE_CUTTHROUGH
Hi Kim, Thank you for the confirmation. I am able to reproduce the error on my side. I am currently investigating why this could be caused. Regards Archit Dev
View ArticleForum Post: RE: TMS320F28335: Letter of Volatility
Hi Benjamin, thank you for the attached. Very much appreciated. Emma
View ArticleForum Post: RE: TMS320F280025C: Motor control SDK general project and...
I found that the value of "motorVars_M1.faultMtrNow.all" is not 0 when the motor starts.
View ArticleForum Post: TMS320F28075: DSP JTAG
Part Number: TMS320F28075 Hi， Can the next two DSPS use the same JTAG port？ Thanks~
View ArticleForum Post: RE: MCU-PLUS-SDK-AM263X: DAC for higher frequencies in AM263x-LP
Hii Fleenor, 1. How 100KHz limit is estimated. Is there any document for the same? 2. Could you suggest any IC which have similar ADC structures like 4 to 5 channels with simultaneous sampling at 4...
View ArticleForum Post: RE: AM2432: Improving MCSPI speed
Hi Sreenivasa, They are testing MCSPI Loopback DMA example lld on launchpad. To better illustrate the issue, the transfer is looped forever. The SPI0_CLK and SPI0_D0 is measured in the above picture....
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: FORWARD_MODE_CUTTHROUGH
Thank you. We look forward to a quick solution.
View ArticleForum Post: RE: AM2434: Secure boot, encryption with OSPI flash expected date?
Hi, When can i expect an answer? It would be very helpful as we could plan our development tasks better. Thanks, Mark
View ArticleForum Post: RE: TMS320F280025C: Motor control SDK general project and...
Sorry,I solved the problem.
View ArticleForum Post: RE: AM2431: Issues arise when receiving a large volume of...
Okay Larry, I will start with MCU SDK 9.2 on AM243x-EVM. [quote userid="574777"...
View ArticleForum Post: RE: AM2432: Improving MCSPI speed
Hello Hang, Thank you Please review the below thread. https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1310321/sk-am62-improve-poor-bandwidth-utilization-on-mcspi-bus Regards,...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: EtherNet/IP Adapter Configuration: Input...
Hi Ryohei, The Industrial Comms SDK v9.2 is available on ti.com at this link : https://www.ti.com/tool/download/INDUSTRIAL-COMMUNICATIONS-SDK-AM243X Regards Archit Dev
View ArticleForum Post: RE: EVM430-FR6047: Water meter error increase as the test progress
Hello Thanks for the reply. I switch only EVM #2 and #3, And I calibrate and test EVM with battery. e2e.ti.com/.../test-result-3.xlsx Despite calibration & testing EVM #2, #3 at the same time, EVM...
View ArticleForum Post: RE: AM2434: How many instance can be added in EtherNet/IP stack
Hi Joshua, The Industrial Comms SDK v9.2 is available on ti.com at this link : https://www.ti.com/tool/download/INDUSTRIAL-COMMUNICATIONS-SDK-AM243X Regards Archit Dev
View ArticleForum Post: RE: AM2432: Improving MCSPI speed
Hi Sreenivasa, Thanks for the info. .Going through the link, I see there's similar issue on AM62. Andreas suggests using dma, which we already did, and using tube mode, which is not very helpful as...
View ArticleForum Post: RE: TMS320F2800157: RAM ECC Test
Thank you for the answer, In the following steps: 1. Walk through an M0 RAM location until every bit has had a single-bit error injected into it. 2. Walk through a M0 RAM location until every ECC bit...
View ArticleForum Post: RE: MSP430FR6047: How to get ADC data(waveform) in the...
HI, It depends. One major aspect is the maximum dTOF value. The maximum ADC capture window at 4M sampling rate should be 125us. So, from my view, if the dTOF is greater than 80~90us than in the ADC...
View Article