Forum Post: RE: Emulator connection terminated with random error message in...
Tjarco,This sounds like a JTAG or (less likely) a reset issue.Can you upload the JTAG part of your design? Specifically I'll be looking at things like whether a pull-down is placed on TRSTn and if so...
View ArticleForum Post: RE: Problems with external SRAM on TMS570
Michael,This issue forces single store instructions (STRxx) to be used instead of the "store multiple" (STMxx) instructions. This essentially prohibits the application from benefiting from the burst...
View ArticleForum Post: RE: CCS 3.3 needed
Brett,We are using a -F2810. Thanks, I will try to post in the tools forum.BR,Claus
View ArticleForum Post: RE: msp430f47197 Energy Meter
[quote user="Tom Harris"]Greetings,Would it be possible to use the msp430f47197 (3 phase energy meter) as a single phase 3 channel meter?[/quote]Yes you can just use TI evaluation board and measure...
View ArticleForum Post: RE: SVS on MSP430F and read/write process through flash
[quote user="Jens-Michael Gross"]Okay, if I understand you right, you want to detect a power loss to save the current state of the application to flash and continue when power returns.[/quote]Correct!...
View ArticleForum Post: RE: I2C with Stellaris LM4F120H5QR - working driver API example code
Hello Sir, I tried to get this library and i got 403 - Forbidden: Access is denied.Is there any way to download it... ?
View ArticleForum Post: TMDSHVMTRINSPIN InstaSPIN
Can anyone direct me to the USB driver for the InstaSPIN kit TMDSHVMTRINSPIN ?
View ArticleForum Post: RE: UniFlash F28069 problem writing to flash
Thank you for the response Mandeep. This solution worked in that it programmed the whole file without skipping sections of memory and without throwing errors. However; it is programming the file byte...
View ArticleForum Post: RE: CCS V5.5 and reserved vectors
[quote user="Bruce McKenney47378"]I suspect the linker was always supposed to act this way, and for v5.5 someone changed it so it works "correctly". Unfortunately, the G2553 (and many other)...
View ArticleForum Post: RE: Block diagram of a balancing robot, is it possible?
[quote user="hau-shiue Juang"]In other words, can the TIVA development board send the control signal to control the torque by motor board, and motor control board also feedback the data of wheel...
View ArticleForum Post: RE: How to modify Java_HID_Demo in MSP430 USB packakage?
Hello Hoa,The HIDAPI source file that you are looking at is specifically made to work with Java. It is meant to be built into a DLL that Java uses to communicate with the HID layer in the operating...
View ArticleForum Post: RE: External Voltage is too low: 1.7 volt
CaEngineer,Just out of curiosity if you hook a multimeter up to the EXT voltage pin on your evaluation board, what is the voltage reading for the multimeter?Also, would you be able to provide the model...
View ArticleClik here to view.
Forum Post: RE: Code Compeser Hex File
Eoin,It would appear that your screenshot did not go through. Would you mind reposting it?The option you are looking for should be under the "Apply Predefined Step" under the Build settings of the...
View ArticleForum Post: RE: How can I get the source code of Flash API ?
[quote user="Igor Gorbachev"]Unfortunately it is impossible http://e2e.ti.com/support/microcontrollers/c2000/f/171/p/272631/953036.aspx#953036[/quote]I am not sure that it is impossible - since that...
View ArticleForum Post: RE: InitFlash on F28069 controlSTICK
Hi Anandhi,There isn't a strict definition for the 'X' you describe. In most application code we see about 10% - 20% improved performance when code is run in RAM as opposed to FLASH. C2000 devices'...
View ArticleForum Post: RE: Connnection problem between XDS100v2 ARM and TM4C123GH6PGE
Hello,Could you please post more of your schematic, so that I can see the JTAG connections going to the TM4C123GH6PGE?-David
View ArticleForum Post: RE: Keil debug fail with stellaris launchpad.
@ Craig,Received, understood, all clear now! Thank you for an especially clarifying & "crack of the bat" response - much appreciated...Professor Chen & my group have exchanged privately in the...
View ArticleForum Post: RE: Determine ADC12 sample rate.
Hello,Thanks for the question and answers. Yet, I have another side question. I was wondering how you measured ADC sampling time.I am converting three signals in the Repeat-sequence-of-channels mode....
View ArticleForum Post: RE: Cannot flash any 9B96 parts with common date code - do I have...
Can you please answer/send the following:1.) Schematic. If you do not want to post here, I will send you an email to the address you registered with for you to respond to. At a very minimum, the...
View Article