Forum Post: RE: Combining CCS code with Energia Sketch
Hello LAXMI KANT TIWARI, You can combine CCS code with Energia Sketch in 2 ways: 1. Use Energia Sketch and place in it CCS code (with adjustments, if they are required). This way always works. 2. Use...
View ArticleForum Post: RE: F28377S sci_echoback_cpu01 clocking and BAUD issues
Hi Taisen, What version of SW for F2837xS device you are using? I'll inform controlSUITE team about the same so that it can be fixed in next release. Regards, Vivek Singh
View ArticleForum Post: RE: High Speed Pulse Counting with MSP432?
[quote user="Ryan Brown1"] 9 ns is equivalent to 111 MHz which is far too fast to be counted by any MSP devices. Even the TimerD peripheral which exists solely on F51x1/F51x2 devices is only capable of...
View ArticleForum Post: RE: Beginner problems with the F28377S Launchpad - Where to...
Hey, thank you very much for your quick answer. I did go through the file F2837xS_SysCtrl.c but it is more confusing than explaining to me :) In that particular file, the function InitSysCtrl(void) is...
View ArticleForum Post: RE: Debugging watchdog on TMS570
Thank you, In case you need any further information, let me know. I think that the code that I enclosed is enough to reproduce it on the TMS570LC4357 target. Piotr
View ArticleForum Post: RE: Hercules RM48L952ZWT - Force HALT in case of critical...
Tammy, The CPU continues to fetch instructions on each clock cycle unless it goes to an IDLE state. However, it is certainly possible to implement a trap (e.g. while(1){}). This trap will stop...
View ArticleForum Post: RE: MSP Flasher --- MSP430 Does not work after installation!
Ashka, Here is my findings so far: I have successfully done what you have done above as you can see through the pictures below. However, when I load the firmware to the MSP430, my LCD does nothing!...
View ArticleForum Post: RE: Error in RM57 TRM?
Thank you. We will correct the figure titles, and show all 12 bits in figure 27-10.
View ArticleForum Post: MSP430F5510 LPM3 reseting MCU
Hi Im having a n issue with the LPM3 and the enumeration of the USB. The Programmers guide states that when the host goes into ST_NOENUM_SUSPENDED mode we should treat this mode like it is disconnected...
View ArticleForum Post: RE: F28377S sci_echoback_cpu01 clocking and BAUD issues
Hi Vivek, I am using v3.3.7 - November 13, 2015 controlSUITE , I believe that is the newest version. That would be great! Thank you Viviek. Best Taisen
View ArticleForum Post: RE: Unable to send more then 8 bits on SSI
Well if you haven't guessed by looking at the screenshot, the MISO line is low. Due to a wiring error the line was being held high and the MCU was waiting for a response which is why the second byte...
View ArticleForum Post: RE: USB bulk code doesn't finish initializing
Hello John, I meant the source project that you are using? Regards Amit
View ArticleForum Post: RE: Simple step-by-step for programming into flash for TMS320F28xxx
Dear Heustess, I finally realize the problem, somehow in my F28027.cmd linker file, it dont have "LOAD_SIZE(_RamfuncsLoadSize)," line. I just simply add the line and finally it works. SECTIONS {...
View ArticleForum Post: Create a Binary
Going through the Instaspin GUI quick start guide, and I have been asked to; "create a binary from any motorware project using ccstudio " How do I do this? What is a binary in this instance? Thank you
View ArticleForum Post: MSP-FET 430UIF USB-Debug-Interface error
I have a MSP-FET 430UIF USB-Debug-Interface that I am trying to set up using the FET-Pro430 Flash Programmer Lite software. After installing the software (which included installing a USB driver and...
View ArticleForum Post: RE: Why are there 3 ADC0 event Mux trigger sources possible for 3...
[quote user="BP101"]Seems I am on to something here[/quote] Would not that, "On to something here" be far better supported with the display of the more normal/expected, "Wider PWM" drive signals? Are...
View ArticleForum Post: RE: freopen and SCI_open from F2837xS_sci_io.c on F28377S LaunchPad
Hi Waldemar, What are you trying to accomplish in your system? Are you using controlSUITE ? Where is freopen() defined? There are some other functions that may be useful for you in F2837x_common\utils\.
View ArticleForum Post: RE: TIVA UART IRDA between two TM4C boards.
I've continued work on this project and I have the following dilemma. The onboard temperature sensor is stored into a 32 bit variable, but only 12 bits are actually used. I then want to transfer that...
View ArticleForum Post: RE: Hercules RM57 Initialization Code
(Please visit the site to view this file) I have attached the GNU .out file with no modifications to the Halogen HAL code to demonstrate the issue. To recreate the failure power down the board...
View Article