Forum Post: RE: TMS570LS3137: We need MCAL for TMS5703137DPGEQQ1 and...
Dear Sirs, In Poland TI have no TI local sales. With who am I contact ? I called TI Germany but with no effect. I contacted with TI Customer Support CS0700029, CS0737113, CS0744610 still nothing. I...
View ArticleForum Post: RE: MSP430FR5043: No acknowledgement after slave address
Check your board's schematic to see what the /RESET pin (2 or 16, depending on the package) of the AD5122A is connected to. If it's being held low (GND) I expect the device won't respond. The data...
View ArticleForum Post: RE: TMS320F28379D: Reading data from FLASH
Hi, Anu: I cannot see the contents of the buffer written to FLASH in the memory window. [quote userid="487101"...
View ArticleForum Post: RE: TMS320F28379D: Processor load Simulink block functionality &...
Thank you. I have been looking at the linker MAP file and would appreciate any advice on which hexadecimal memory addresses I can subtract to obtain a hexadecimal value of RAM memory used. I have...
View ArticleForum Post: TM4C129XNCZAD: Real Time Clock lagging
Part Number: TM4C129XNCZAD Dear Sir, We have developed our own PCB board with TM4C129XCNZAD and using the inbuilt Hibernate RTC feature of processor. Initialization code void Hibernate_RTC_Init(void)...
View ArticleForum Post: RE: MSP430FR2433: I2C communication error
What exactly are you sending (to get back the 0x80-s)? I'm not familiar with this device, but maybe someone will see something. I wasn't able to find a protocol definition (the NXP data sheet mostly...
View ArticleForum Post: RE: TMS570LC4357: HAL Code Generator example_mibspiDMA extended...
Hi QJ, thanks for your proposal for solution. I extendet the code as shown below. The received Date in the RAM location after DMA transfer looks fine. Unfortunately this solution involves the CPU. Is...
View ArticleForum Post: RE: TMS320F28069: Bootloader DFU on conltrolCARD F28069 :...
Hello , some news I view in this topic : (+) USB bootloader along with dfuprog exe - C2000 microcontrollers forum - C2000 ︎ microcontrollers - TI E2E support forums that some code was modify. " The...
View ArticleForum Post: RE: MSP430FR2512: Problem with I2C in Design Center, no "HID...
Hi Sebastian, Yes, you need to set the P1SEL.2 = 1 and P1SEL3 bits = 0 accordingly. . According to the datasheet, P1.2, P1.3 are available as I2C pins. You don't need to change USCIBRMP, so you should...
View ArticleForum Post: RE: MSP430FR5043: No acknowledgement after slave address
Hello Bruce, [quote userid="47378"...
View ArticleForum Post: RE: TMS570LS3137: Need TI FatFS library for TMS570LS3137WZT,...
Here is the SD card example using RM48 MCU: e2e.ti.com/.../3157.RM48-HDK-RevE-SDCard-Demo.zip
View ArticleForum Post: RE: MSP430FR5733: Internal resistance values of P1.0 and P1.3
If they are using a high-voltage ohmmeter they might be measuring the ESD diodes. Have them measure both polarities.
View ArticleForum Post: C2000WARE: Can higher priority interrupt executions at high...
Part Number: C2000WARE Hello, I am developing a dual-CPU power converter. I have one converter running at 1MHz and the other running at 200-400kHz, and their interrupts are triggered by the ADC SOCs....
View ArticleForum Post: RE: TMS320F28388D: Get 0% or 100% duty cycle with HRPCTL[HRPE]=1
Hi, You can change the duty cycle from 0-100% but the limitation still applies. When the edge falls during those cycles, High resolution portion will not work as expected in those cycles. So, if this...
View ArticleForum Post: RE: MSP430F5638: Driving a microsd card via SPI from MSP430F5638
David, Thanks for the SparkFun link, I'll take a look at that.
View ArticleForum Post: RE: TM4C129XNCZAD: Real Time Clock lagging
Hi Rajesh, - Can you run the TivaWare hibernate_calendar example on your custom board? Perhaps you need to modify it so that it will go hibernate for a longer period of time. Can you repeat the same...
View ArticleForum Post: RE: TMS320F28374D: CAN losing data in transmission
HI Hareesh , Baud rate is 500KB/s and it seems messages lost when delay < 1mS , maybe since we are in CAN open PDO and some async messages coming . I ll give you feedbacks on your suggetsions thank...
View ArticleForum Post: RE: Why are there only 2 base addresses for 3 GPIO modules?
Hello Philip, I have sent your thread over to our MCU+ team. Please ping the thread if you do not get a response in a day or so. Regards, Nick
View ArticleForum Post: RE: MSP-EXP432P4111: [ACK_ERROR_MESSAGE]Header incorrect! seen,...
ok, the github code does not provide host drivers, but I'm working that now. related question, the data block command takes an address, which I assume is the base address for the 432's executable...
View Article