Quantcast
Channel: Microcontrollers
Browsing all 226135 articles
Browse latest View live
↧

Forum post: RE: TMS570LS3137: ESM Group3 RAM even bank ECC error on cold boot

Hi Chuck, Were you able to replicate the issue today? Regards, Sunil

View Article


Forum post: RE: CCS/MSP430FR6989: MSP430 interrupt with delay coding problem

Hi Bruce, Sorry, I forgot to awnser "What do you expect will happen when the switch is switched? The ISR takes no (visible) action." So my goal is to generate a blinking LED with a duty cycle of...

View Article


Forum post: RE: CCS/TMS320F28379D: Compiler v18.12.3.LTS custom library creation

Nagesh, I have sent you a 'friend request' on the forum with additional information on how to start this process. I will close this thread as we will handle this off forum. Regards Lori

View Article

Forum post: CCS/MSP432P401R: MSP432P401R Rev D Bricked. Tried factory reset...

Part Number: MSP432P401R Tool/software: Code Composer Studio I have an MSP432P401R Rev D (as per the chip itself) using a XDS110-ET Debugger. I have been using this board without issue for the semester...

View Article

Forum post: RE: SIMPLELINK-OPENOCD: Selecting one among multiple connected...

Hi, You should be able to select by serial number. For example, if you have multiple launchpads connected to your PC, you can see them enumerated in Flash Programmer 2 with unique serial numbers:...

View Article


Forum post: RE: TMS320F28388S: CLB doubt

MODE is level based. Counter module in "counter mode" is always counting the clock cycles. If you want to provide the clock, configure it as an adder with an add of "1" when the EVENT signal edge...

View Article

Forum post: RE: TMS570LS3137: ESM Group3 RAM even bank ECC error on cold boot

Hi Sunil, Thanks for the follow-up. I have issue the "debug without downloading command" from the IAR interface, and it does connect without error. However, I suspect that the CPU is lost somewhere,...

View Article

Forum post: RE: TMS570LS3137: Clarification on mibspi parity transmission

Hello, The parity value is not in TXRAM region or RXRAM region. The parity value are located at RAM_base address + 0x400 (parity RAM region). For MibSPI1, Buffer0: RX RAM address: 0xFF0E0200, Parity...

View Article


Forum post: TMS320F28379D: Hardware Design reference for field programming

Part Number: TMS320F28379D Hi I am in the process of designing a board based on TMS320F28379D which needs field programming via RS232. So requesting members for providing Hardware design guidelines.

View Article


Forum post: TMS570LS3137: Code for MIBSPI to check parity

Part Number: TMS570LS3137 Hi, Please find the attachment of the main file to use mibspi for sending the data '3' continuously using external loopback. Here, the odd parity is considered. How is the...

View Article

Forum post: RE: TMS320F28379D: Usage information on TRREM register for...

Okay here is the latest content I have: 1. with HRPE=0, the TBPSHR operates as expected. 2. For PHSDIR = 1, negative phase values: the desired value need to be subtracted from 0xFF (this will be added...

View Article

Forum post: RE: CCS/TMS320F28379D: XOR of 3 PWM signals

Correct they are two different methods as you mentioned!

View Article

Forum post: RE: TMS320F280049: CMPSS query to implement peak current mode...

Tony, As I indicated above, the CMPSS DAC has an inbuilt RAMP generator which is only falling. I have recommended to you two methods as work around 1. Use a rectified current signal such that ramp is...

View Article


Forum post: RE: CCS/TMS320F28377S: ABC to DQ0 Current Transformation

Thanks for confirming, I have closed the thread. Best of luck with rest of your project.

View Article

Forum post: RE: CCS/MSP432P401R: Temperature Reading

Yash, We do not support MSP432Ware anymore as this has been superseded by the MSP432 Software Development Kit (SDK). I recommend you download and install the SDK, then check out the "i2ctmp" example...

View Article


Forum post: RE: TMDSCNCD28388D: New dsp TMS320F28388D overview

Hi Adrien, Glad to hear you are moving to C2000. 1. Yes, you absolutely can use F2838x for TIDM-1000 and we already have TIDM-1000 reference code based on F2838x in Digital power SDK so you can refer....

View Article

Forum post: RE: TMS320F28377D: MAXIMUM CLOCK SETTING at 200Mhz

Hi Pete, Did you get a chance to check out the clock settings and validate that SYSCLK is running at 200MHz? Let me know if you still have issues with clocking. Best regards, Joseph

View Article


Forum post: RE: TMS320F280049C: how to prevent RAM content change after flash...

Does flash programming perform a POR that clears the RAM to 0x0?

View Article

Forum post: RE: CCS/LAUNCHXL-F28069M: Pulse and direction drive using...

You can find the sensored-FOC PMSM references in the folders of controlSUIE as the link below, or MotorControl SDK that just has a reference for F28004x, F2837x and F2838x....

View Article

Forum post: RE: TMS320F28377D: RAM memory map and CPU access

Hi Subash, Let us know if this issue is resolved. Vivek Singh

View Article
Browsing all 226135 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>