Forum post: CCS/MSP430FR6989: MSP430 interrupt with delay coding problem
Part Number: MSP430FR6989 Tool/software: Code Composer Studio Hi, I have attached a switch to port 2.0 and a led to port 2.4. I am trying to figure out how interrupts work with a delay timer, I thought...
View ArticleForum post: CCS/TMS320F28069M: Timer to read pwm duty cycle?
Part Number: TMS320F28069M Tool/software: Code Composer Studio Hi, I have been searching various forums with no good results here. I am using the F28069 in a project where I need to read input PWM as...
View ArticleForum post: TMS320F28335: ADC register could not be written rightly
Part Number: TMS320F28335 Hi Expert, Customer met a problem that the ADCTRL3 content should be written as 0x00E7, however after run through the configuration code, The AdcRegs.ADCTRL3.all = 0x0007. ADC...
View ArticleForum post: TMS320F280049: How to choose the optimization level in CCS...
Part Number: TMS320F280049 Hi Expert, Could you suggest that how to configure the below items to optimize the program running speed while maintaining code integrity? Thanks! Best regards Rayna Wang
View ArticleForum post: MSP432E401Y: BSL-Scripter 3.4 E4xx DFU Erase block bug
Part Number: MSP432E401Y It is impossible to erase a block higher than 1FC00 with BSL-Scripter 3.4. But with MSP432E401Y, the flash memory go up to 0x100000. Found this into BSL Scripter: In file:...
View ArticleForum post: CCS/TMS320F28379D: TMS320F28379D
Part Number: TMS320F28379D Tool/software: Code Composer Studio Hello, I want to measure output across a DACOUT pin which is given as input across a ADCIN pin. But I am not getting any output across the...
View ArticleForum post: TMS320F28069F: [Instaspin]: Doubt about no motor detection
Part Number: TMS320F28069F Hello! I have an Instaspin FOC based application. It runs the Speed Control lab correctly and now I have to develop the failures detections to avoid dangerous situations...
View ArticleForum post: MSP-EXP432P401R: Interrupts not detected on Port 2
Part Number: MSP-EXP432P401R I'm struggling to get interrupts working on Port 2 of the MSP-EXP432P401R dev board. I've disconnected the jumpers going to the LEDs and tied in external switches. I can...
View ArticleForum post: TMDSCNCD28388D: New dsp TMS320F28388D overview
Part Number: TMDSCNCD28388D Hi, I'm an engineer in power electronics and my goal is to migrate from Microchip DSP to TI DSP. I have a similar question as above: can we use the TMDSCNCD28388D control...
View ArticleForum post: TMS320F28379D: TMS320F28379D
Part Number: TMS320F28379D Clayton: got a new project: 270VDC input to 34v 300amp output. We still want to use CPU1 for FB_LLC and CPU2 for yet another Interleaved HB_LLC. I can look into Dual active...
View ArticleForum post: RE: TMS320F280049C: how to prevent RAM content change after flash...
Hi, [quote] Does the variables get zero value if they are not initialized? for example int xx; without assigning any value to it, has initial value of zero? or gets it's RAM address content? I know in...
View ArticleForum post: RE: CCS/TMS320F28377D: GUI composer using 28377D
For custom protocol, you would need to write JavaScript code to parse the data. https://dev.ti.com/gc/designer/help/GC_UserGuide_v2/targetprog.html#usb-uart-custom We do not have any examples for...
View ArticleForum post: RE: TMS320F28335: ADC register could not be written rightly
Rayna, At the moment, I do not think that it is a board-level issue. Do note that the ADC_cal() function only needs to be executed once. If it is executed more than once in an example, it is not done...
View ArticleForum post: RE: CCS/TMS320F28377D: CCS/TMS320F28377D: Real-time debugger...
Thank you for your feedback. We'll see if this can be addressed in next release of the document. Regards, Vivek Singh
View ArticleForum post: RE: CCS/EK-TM4C123GXL: Boostxl-k350qvg-s1 not displaying.
Greetings, [quote user="Chester Gillon"]don't currently have the ability to remove surface mount components).[/quote] Feel your pain - yet: application of absorbent 'solder wick' (to each end of the...
View ArticleForum post: RE: TMS320F280049: ECC error
Emma, Do you have an update on this? Thanks and regards, Vamsi
View ArticleForum post: RE: TMS320F28335: Sample code to interface...
Sachin, It has been a while since your last update. I assume that you were able to resolve your issue. If not, please reply to this thread. If the thread has locked due to timeout, please create a new...
View ArticleForum post: RE: TMS320F280049: CMPSS query to implement peak current mode...
Manish, If I understand correctly, I can use the internal DAC of the CMPSS module to generate a rising and falling ramp signal?
View ArticleForum post: RE: TMS320F280049: Type 4 PWM AQ submodel T1 or T2 event
Can you divide your period value by three so you can use them accordingly? You can scale other PWM values as well.
View ArticleForum post: RE: RM57L843: leakage current and low power mode current
Internal char data shared privately. Closing this thread.
View Article