Forum Post: TM4C123GH6PM: Adding Parity to UART1
Part Number: TM4C123GH6PM I'm having trouble trying to initialize my UART with an odd parity. I was originally using the following, which configures the UART with no parity:...
View ArticleForum Post: MSP430F67461A: MSP430F67461A controller reset during mains ac...
Part Number: MSP430F67461A I have single phase energy meter with MSP430F67461a controller the problem is when ever i am touch the main ac supply point controller is getting reset. i have connected the...
View ArticleForum Post: MSP430FR2522: Unexpectedly high power consumption in LPM4 mode
Part Number: MSP430FR2522 I am developing an application with the MSP430FR2522 where I need Very low average power consumption (1-10 uA at 3V) To keep track of time using the RTC module Basing on TI's...
View ArticleForum Post: RE: MSP430F5659: USB Disconnection Issue
Hi, Is there any more support needed for this issue? If so please reply with any relevant details so that I can further assist you. For now I will be marking this thread as "TI Thinks Resolved". If you...
View ArticleForum Post: RE: TMDSEMU110-U: tmdsemu110-u Energy Trace not working correctly
Hi Rafael, For the 600uA issue I see the same. The JTAG connector only needs to be connected with no Debug session initiated to record 650uA. Then with JTAG connector removed: 50-60uA. Then with the...
View ArticleForum Post: RE: EK-TM4C123GXL: is not detected by pc
I cannot use lm flash programmer because pc cannot connect to device and I didnot use DFU update best regards, hisham elreedy
View ArticleForum Post: RE: CCS/RM48L952: debug stop at b prefetchEntry
Hello, When a prefetch abort occurs, the CPU marks the prefetched instruction as invalid, and all the p-aborts are precise abort. Please check the value in the link register (r14_pabt) to determine...
View ArticleForum Post: RE: CCS/TM4C1294NCPDT: warning: statement is unreachable
[quote user="harshal patil"] Please find attached file for project which I've created using CCS v9.0.1. Please refer build log for attachment. build_log.txt [/quote] Harshal, For this project, you can...
View ArticleForum Post: RE: EK-TM4C123GXL: is not detected by pc
If the ICDI device was damaged by ESD then the EK-TM4C123GXL needs to be replaced. Unfortunately I have no other debug suggestions.
View ArticleForum Post: RE: CCS/TMS320F28027: C2000™ microcontrollers forum
Hi, You can refer to 3.2.7 Trip-Zone (TZ) Submodule in the device TRM http://www.ti.com/lit/ug/sprui09/sprui09.pdf Run the Trip zone examples specified earlier, modify the code as you need and try to...
View ArticleForum Post: CCS/TMS320F28377S: Load program Error
Part Number: TMS320F28377S Tool/software: Code Composer Studio Hello guys! Please, help me... Every time I try to run a debug from FLASH, or just a simple load, I get the following message on console:...
View ArticleForum Post: RE: MSP430FR2355: LaunchPad MSP430FR2355 is not loading the code...
Hi What's the states of the LEDs(LED101 and LED102) on the eZ-FET? For the meaning of the if you can refer to the MSP debuggers user's guide 5.8.3 Have you try other PC? Gary
View ArticleForum Post: RE: TIDM-HV-1PH-DCAC: ADC Sensing - Incorrect readings
Robin, Ok, considering Vref is now in range. Can you elaborate on how much is the error now ? You can run the build level 1 under DC and see the sensing more precisely.
View ArticleForum Post: RE: TIDM-1000: What does ADC_PU_SCALE_FACTOR represent?
[quote user="stevenh"] I simulated the feed back circuit in TINA (see attached file). For a 416.917V input, the simulation gives a feedback value of 3.2Vpeak. That is greater than what I thought was...
View ArticleForum Post: RE: TMS320F28379D: High-Resolution PWM Control mismatch with...
Hi, [quote user="Alon Harpaz"]One thing which I already noticed - the SFO() result (as read from EPwm1Regs.HRMSTEP.bit.HRMSTEP is 130, which is roughly TWICE the value that was obtained with my setup,...
View ArticleForum Post: RE: MSP430FR2155: ADC12 Repeated Sequence of channels sampling...
Hi Deepak Do you have a MSP430FR2355 's Launchpad? Have you try this on the Launchpad?
View ArticleForum Post: MSP432P401R: Connecting 12 ADS8688's to MSP432 with SPI
Part Number: MSP432P401R Hi, I have this battery system that is wired as 8 parallel columns of 6 series batteries (48 total). With each battery roughly 1.5 V each, each column has 9 V at the top. I am...
View ArticleForum Post: TMS320F28376S: CLA - DMA accessibility
Part Number: TMS320F28376S Dear Sir , We have prototype board that we recently got and we are doing bring up testing , the board include TMSF28376SZ and plan to use the CLA to do some calculation in...
View ArticleForum Post: WEBENCH® Tools/TMS320F28388D: Connect Ethernet with RMII
Part Number: TMS320F28388D Tool/software: WEBENCH® Design Tools How do you connect the phyical layer of the Ethernet to the PHY with RMII? I found this in the TRM: and ths in the datasheet of the...
View ArticleForum Post: INSTASPINFOCMOTORWAREGUI: Which device could support Motorware...
Part Number: INSTASPINFOCMOTORWAREGUI Hi , My customer use F28069 control card evaluate vibrate compensation based on Motorware lab11b example. The performance is very good. They would kick off a...
View Article