Forum Post: RE: CCS/TMS320F28069: MOTORWARE
Hi Sudhakar, Thank you for your response. I did it and it Connected, but another error (no symbols are defined for "0x9000" ) mentioned by software. In the console window write: "CLA_0: Can't Run...
View ArticleForum Post: RE: MSP430FR6989: MSP430 JTAG interface for ESD protection
Hi Walther, I'm sorry to reply late. I told the customers that the TEST and RESET pins are very sensitive and that PCB layout (long traces and a connector) needs attention. I'm checking with customers...
View ArticleForum Post: TM4C1294NCPDT: Long Ethernet link up time
Part Number: TM4C1294NCPDT Hi. We are using TM4C1294 MCU in internal PHY mode for Ethernet. Problem: Linking sometimes takes up to 30 seconds, sometimes doesn't even link, rare cases it gets link in...
View ArticleForum Post: RE: TM4C1294NCPDT: Long Ethernet link up time
Here is schematics of our Ethernet connection. Connector used is 6605834-1. I also tried LMJ2018814100DT1 but with no positive results.
View ArticleForum Post: Compiler/TMS320F28069: Code for programming SPI EEPROM
Part Number: TMS320F28069 Tool/software: TI C/C++ Compiler Hello. We have a PCB containing a TMS320F28069 . We now want to program some calibration data (only about 20 int32 integers) into an EEPROM...
View ArticleForum Post: RE: TMS320F28379D: Is the CMPAM register gone?
Hello Nima, Actually I wanted to be able to check whether a given value written to the shadow register has been transferred to the active register. The solution I found is to read CMPCTL[SHDWAFULL] and...
View ArticleForum Post: TMS320F280049: CAN-A data in buffer is different with the data...
Part Number: TMS320F280049 Hi， CAN-A (CAN_OUT) and CAN-B (CAN_IN) share one interruption function in boot-loader. It needs CAN-A and CAN-B during firmware upgrade. The data in CAN-A buffer is not same...
View ArticleForum Post: TMS570LS0714: F021 Flash API Version Reference Guide question
Part Number: TMS570LS0714 Hi Champ, From SPNU501G --F021 Flash API Version 2.01.01 Reference Guide Appendix C Flash Validation Procedure,There has following description: 2. Using the TI profiling tool...
View ArticleForum Post: RE: INSTASPINFOCMOTORWAREGUI: Implementing LAB21 of motorware on...
Respected sir, There is further progress. I have managed to oscillate the rotor. It making one or two revolutions but with lot of oscillations and instability. So on which parameter i should focus??...
View ArticleForum Post: RE: TMS570LS1224: Clear RAM when reset TMS570
Hello David, RAM is initialized by default in "sys_startup.c" generated by HALCoGen . After reset, the code from _c_int00() is executed. Inside _c_int00, memoryInit is the place where...
View ArticleForum Post: RE: MSP430FR2633: CapTivate Design Center doesn't display sensor...
Hi Lennart, any update on the progress. Thanks Regards Kostas
View ArticleForum Post: RE: MSP430FR2522: Touch capacities
Hi Davide, do you have any additional questions to the recommendations given above? Regards Kostas
View ArticleForum Post: RE: TMS320F280049: CAN-A data in buffer is different with the...
Hi Daniel, Do you intend to use CAN A and CAN B in the example you shared? If yes you are configuring the ISR to get interrupt on CAN B in DCDC_CANMBOXS_Init(). That is something i can't see in the...
View ArticleForum Post: RE: TMS320F28335: Controller having problem in CAN reception
Hi, Any update. Regards Harshmeet
View ArticleForum Post: TMS320F28069: Microcontroller with Powerline Communication
Part Number: TMS320F28069 Hello, I would like to get more knowledge about TI's MCU with powerline communication functionallity and I am looking for some kind od dev kit. I found information with C2000...
View ArticleForum Post: RE: CCS/TMS320F28377S: Problem in running "usb_host_msc" from FLASH
Hi Sam, I am trying to debug this. Please expect a reply shortly. Regards Harshmeet
View ArticleForum Post: RE: MSP430F6736: MSP430F6736 IPZR
Hi Behailu, Thanks for the kind feedback! Just to clarify, you're saying that the reset issue has been resolved by switching the pull-up source of the RST resistor from VDSYS to +3.3V, correct? If so,...
View ArticleForum Post: RE: CCS/MSP432P401R: MSP432 I2C connect problem
The maximum I2C clock frequency for the AD7150 is 400Khz and in the i2c configuration the frequency is set to 1Mbps, EUSCI_B_I2C_SET_DATA_RATE_1MBPS. I would recommend utilizing the examples found in...
View ArticleForum Post: RE: CCS/LAUNCHXL-F280049C: SYS/BIOS
Hi, Thanks for the reply. Even I thought so, as aren't sample examples supposed to work out of box if you select the right part number. Earlier I was using CCS Version: 7.1.0.00016. I complies smoothly...
View ArticleForum Post: RE: CCS/TMS320F28335: Help for switching frequency for sinusoidal...
Cody, If it is like you said, can i fix it to obtain frequency at 100 kHz? Regards, Ali
View Article