Forum Post: RE: TMS320F28035: ePWM7 timer in 64pin
Hi Cody, Thanks for your reply! Just double confirm, so this means customer also can use PWM7 timer and interrupt event in 64pin? it is only no ouput pin, right? Best regards, Curry
View ArticleForum Post: RE: TMS320F280049: How to read two continuous frames using...
Hi Linda, Are you using a C2000Ware example? Is there a delay between the two data frames that you are sending? Please let me know some more details so that i can help. Thanks and Regards Harshmeet
View ArticleForum Post: RE: CCS/TMS320F28377D: TMS320F28377's SDFM model comprehensive...
For detect two phase Curent(eg A,B).one method:detect both use SD1,other method: SD1 detect A phase,SD2 detect B phase. Are the two methods the same? Is the timing the same? Best Regards,
View ArticleForum Post: RE: CCS/MSP-EXP430FR5994: problem running software example for...
I got cold. That is why I was silent. Using CCS v8.0, TI compiler v16.9.7.LTS and Project Properties -> General -> MPU tab and MPU turned off I have recording and playback running. Have a nice day!
View ArticleForum Post: LAUNCHXL-F28377S: How to time CLA code?
Part Number: LAUNCHXL-F28377S I have a timed CPU function that I have copied to run as a CLA task. I know it is accessing LSx memory and GPIO registers correctly, but it is not functioning properly...
View ArticleForum Post: RE: TMS570LS3137: VCC slew rate recommandation and impact
Hello OZ, We don't have specific requirement for VCC slew rate. Hercules has a built in module called VMON (voltage monitor module). The voltage monitor generates the Power Good MCU signal (PGMCU) as...
View ArticleForum Post: RE: LAUNCHXL-TMS57004: SPI communication between TMS57004 and...
Hi Gunit, If you only use TMS570 as master, you don't need the slave code on TMS570. TMS570 MCU supports those 4 clock modes, and each mode is defined in the following table: Both master and slave...
View ArticleForum Post: RE: TMS320F28377D: TMS320F28377D
Hello Bharadwaj, Yes you can put both the tasks in one ISR . There are some peripheral register write/read protection from CLA. They can be given access to CLA using MEALLOW function if you get any...
View ArticleForum Post: RE: TMS320F28335: Firmware update on F2833x
This is what I thought in first place. But for this to be working, I need to have boot from SCI setting in bootrom. But my code must have boot from flash setting because my code will be in Flash at the...
View ArticleForum Post: RE: RTOS/TM4C1294NCPDT: TCP Echo example on Custom board
Respected sir, [quote user="BP101"]Even if you use web browser for this forum there will be entries in the ARP table. My friend you may have bigger problems than what you have figured[/quote] While...
View ArticleForum Post: ABOUT PIN CONNECTION
HI I have one query on ADC, AD1EVT Pin:- We are using TMS5700714APZQQ1 controller, in that we have AD1EVT can we leave this pin open does that have any impact. Can you share these details ASAP.
View ArticleForum Post: RE: TMS320F28335: TMS320F28335ZHHA,getting heated up
Hi Cody, 1. the current is being supplied by tps767d301 ldo. The current drawn by the dsp is approx 280 ma. This ldo is kept nearby to the dsp. If there is an email id I can send the schematics for...
View ArticleForum Post: RE: TMS320F28069: F28069 CAN send and interrupt
Yes our can network works fine, and about the id we just put the 0x01 slandered id at both sides tx and Rx devices. while we are testing polling mode we use the "Example_2806xECanBack2Back" project...
View ArticleForum Post: TMS570LC4357: Vulnerability of TMS570LC4357
Part Number: TMS570LC4357 Hello, TI Experts, Our customer sent us a question about below vulnerability for TMS570LC4357 . https://www.kb.cert.org/vuls/id/180049 (It seems to be described about Variant...
View ArticleForum Post: RE: TMS320F28335: hex file
Hex file typically contains the binary image (of executable) with address information (and optionally error correction codes). There are different formats in the industry - you can refer...
View ArticleForum Post: CCS/TMS320F28377S: regarding the digital filter in comparator
Part Number: TMS320F28377S Tool/software: Code Composer Studio how does the sampwin and thresh system work in the digital filter ?i have read the trm, but didn't quite understand it . 1) do the...
View ArticleForum Post: RE: CCS/MSP432P401R: how to change the clock divider in run time
Andrew, You can change the clock divider by writing to the CSCTL1 registers DIVM bit. The simplest way to do this is through the MAP_CS_initClockSignal() API call. For example:...
View ArticleForum Post: TMS320F28379D: CLB tformat clock support?
Part Number: TMS320F28379D Hi, In TIDA-1010 web link, www.ti.com/.../TIDM-1010 It said that this TI-design can up to 5 MHz t-format clock supported. But tidue74.pdf and PM_tformat_Lib-sprui71.pdf shows...
View ArticleForum Post: RE: MSP432P401R: problem with interfacing MSP432 with ADS1292
Shyam, You indicate that the SPI reads to the ADS device are slow "when in debug mode". Does your code work properly when you are not connected to a debugger? Also, are you able to connect a logic...
View Article
