Forum Post: RE: TMS320F280039C: After the EPWM module is configured, does...
Hi Ryan, I understand that eCAP implements functions equivalent to TB, CC, and AQ of EPWM, while DB and TZ functions are not. If eCAP is used, TZ should be combined with EWPM interrupts to stop eCAP...
View ArticleForum Post: RE: MSPM0G1519: TIMG12 capture using external 32MHz clock and...
For IFCTL_01[0], ISEL=0 and ISEL=2 are equivalent (since it's channel 0). One usage for ISEL=2 is to set it in IFCTL_01[1], so both channels use the CC0 pin, then set opposite edge-senses so one...
View ArticleForum Post: MSP430G2553: A/D conversion in DTC mode on multiple channels of...
Part Number: MSP430G2553 Tool/software: Hi team, My account would like to do AD conversion in DTC mode on multiple channels but they could not understand how it operates. They would like to confirm...
View ArticleForum Post: MSP430F5529: Use I2C Module to read data - after set MCLK as 32MHz
Part Number: MSP430F5529 Tool/software: Hi, When I use I2C module of MSP430F5529, some problems happened. I use the following code to send one read-byte signal. ( current MCLK is 32MHz ) The interrupt...
View ArticleForum Post: RE: TMS570LC4357: Can the CPU jump to the FLASH OTP area to...
Sorry, maybe I didn't it well.You are correct, the program must be loaded at address 0 to start. Note that I'm experimenting with bank 7 now, but ultimately it's to experiment with programs in the...
View ArticleForum Post: RE: MSP430FR5994: TI Compiler does not find DSP library functions
Copy the DSP folders include and source into your project such that the paths are now ProjDIR/dsplib/include and ProjDIR/dsplib/source . Then clean your project. After cleaning, go into the active...
View ArticleForum Post: RE: LAUNCHXL2-570LC43: RESET button usage & error messages
Thank you so much, always appreciate you
View ArticleForum Post: RE: TMS320F28379D: EMUSTOP source
Hi Ozino I had read the link provided by you. However, the message is not very clear to explain when EMUSTOP signal will be generated. In TRM, There is not any explanation for EMUSTOP signal. If you...
View ArticleForum Post: RE: TMS320F28P550SJ: CLA fails to write to EPWM after Power Cycle
Hi Donavon, I have a couple of clarifying questions: By "power cycle", which of the below are you referring to? See the TRM section here for descriptions of each. After the power cycle, how are you...
View ArticleForum Post: Processors forum
Part Number: AM6442 Tool/software: 尊敬的技术支持团队： 我们根据您的 AM64x 开发平台设计了一个定制板，使用 AM6442 处理器。将 DDR 芯片更换为新模型后，我们需要重新编译 U-Boot 和内核（Image）。您能否指导我们哪些 文件需要修改 以确保正确的 DDR 初始化和系统稳定性？
View ArticleForum Post: RE: MSPM0L1228: enable VBAT but fail to boot up
Pengfei, I use newest EVM. rev.A. fw change: DL_SYSCTL_enableSuperCapacitor() EVM jumper change: as below. BR, frank
View ArticleForum Post: MSP430FR6047: Pin_Configuration in Mains And Battery Mode
Part Number: MSP430FR6047 Tool/software: Hi, I need to know what should be condition of my TEST pin in normal mode when am not into debugging mode both for Mains & Battery Mode.
View ArticleForum Post: RE: MSP430G2553: A/D conversion in DTC mode on multiple channels...
1) Yes. [Repeated] Sequence of Channels mode counts the channels down from INCH -> A0, so in your case A7 would be the first entry. 2) ADC10IFG is triggered when the count (ADC10DTC1) is exhausted...
View ArticleForum Post: RE: MSPM0G1507: Are there any registers or settings that can...
Yes, depends on the requirements.
View ArticleForum Post: RE: MSP430F5529: Use I2C Module to read data - after set MCLK as...
I'm pretty sure the F5529 is limited to 25MHz [Ref datasheet (SLAS590P) Sec 8.3 "Fsystem"] Do you see this behavior with MCLK=25MHz? What is your slave device? Is there a reason it might reject a...
View ArticleForum Post: RE: MSP430F5529: Use I2C Module to read data - after set MCLK as...
Hi Bruce, Thank you for your reply. 1. About the MCLK, I have test the MCLK output it is really the value I set (32MHz), according to current test, MCLK can over the spec. Because of other function...
View ArticleForum Post: RE: MSP430F6638: MSP430F6638 controller config using JTAG...
Hi Jithin, I see your previous thread, can you share your PC management screenshot, I suspect there is no available driver. B.R. Sal
View ArticleForum Post: RE: EVM430-FR6047: error #10010: errors encountered during...
Hi NGO, Okay, let take download it and take a try. Will update my test result by tomorrow. B.R. Sal
View ArticleForum Post: RE: LP-AM243: LP-AM243 ETHERNET/IP CODESYS EXAMPLES PROGRAM FOR...
I am working on ethernet/ip project use am243 EVM, I purchase the SPI ads8588 DAC, Can I use this program for Ethernet /IP or I need to modify this programs. and how to create and EDS files for...
View Article