Forum Post: RE: TMS320F28377D: global variables in structure are changed...
Unfortunately, this description is too vague. For the source file where the problem occurs, How to Submit a Compiler Test Case . Regarding ... [quote userid="521036"...
View ArticleForum Post: RE: TMS320F28P650DK: Problems connecting to device after programming
Hi Matt, ok I made some progress. Being a hardware engineer I decided to take a look at the status of the JTAG pins when the XDS200 is trying to connect. In the scope plot below, C1 (Yellow) is TMS,...
View ArticleForum Post: TMS320F28386D: XDS110 Debug Probe Adapter Problem
Part Number: TMS320F28386D Tool/software: Hello! I am trying to connect to my target (TMS320F28386D) by way of the XDS110 Debug Probe. The target's connector is the 10-pin ARM while the XDS110's...
View ArticleForum Post: RE: MSPM0G1519: TIMG12 capture using external 32MHz clock and...
Bruce, Would you have a few minutes for a call to explain a few things? (719-502-1675) I am just stuck where I do not under stand the Tech Ref Manual terminology where signals/pins are selected. Can...
View ArticleForum Post: RE: TMS320F28335: How to configure eCAN mail box ID for TMS320F2833x
[quote userid="638648"...
View ArticleForum Post: TMS320F28035: Unable to write to the last 2 bytes of ePWMx CMPA...
Part Number: TMS320F28035 Tool/software: Hello, I have my F28035 microcontroller configured to up/down PWM mode, but it seems that I cannot write to the two least significant bits of the CMPA...
View ArticleForum Post: RE: TMS320F2800137: CAN TRANSMIT NOT WORKING
Hi Muntaha, Are you referring to J14 of the LaunchPad for the PCAN connection? Can you check that S4 is in the correct position to route GPIO4 and GPIO5 to the on board transceiver? On the PCAN side,...
View ArticleForum Post: MSPM0G3507: Using #pragma and section data for MSPM0
Part Number: MSPM0G3507 Tool/software: I'm trying too section off some section of Flash specifically for some constants with the MSPM0G3507 and TI Clang compiler. I have the following lines of code:...
View ArticleForum Post: RE: TMS320F28375D: SCI Boot failure with FMSTAT=01010
Hi Hang, For CCS next steps, are we confirming operation by: 1) Setting the boot mode to 0x815A at address 0xD00 2) Running CPU1 target 3) Run the Serial Flash Programmer w/ example files (If able,...
View ArticleForum Post: RE: TMS320F28P650DH: Flash operation requirements, F28P65 vs F280049
Hi Hang, I am looking into this question to see if there is a particular reason this comment was made for F28P65x. I will get back to you as soon as possible. Best Regards, Marlyn
View ArticleForum Post: RE: TMS320F280049C: Variable range of output voltage in LLC...
Hi Conor, You may take a look at our CLLLC reference design TIDM-02002 https://www.ti.com/tool/TIDM-02002 . It can operate above and below resonant frequency. Thanks Srikanth
View ArticleForum Post: TMS320F2800132: Only half the available flash seems available.
Part Number: TMS320F2800132 Tool/software: I am getting the following error: Loader: One or more sections of your program falls into a memory region that is not writable. These regions will not...
View ArticleForum Post: RE: TMS320F28388D: eCAP Spurious interrupt
Hi Adrien, That is correct. You'll clear the event interrupts, then clear the global interrupt like our examples do in the ecap/ folder within our C2000WARE SDK. This diagram show cases this. If you...
View ArticleForum Post: RE: TMS320F28379D: ADC sensing issue
Hi Deep, Thank you for your response. With 3V input to ADC, I am getting 4095 counts. It seems like internal voltage Vref is 3V. Is there any method by which internal votlage can be measured. As per...
View ArticleForum Post: MSP430FR6047: Schematic Review
Part Number: MSP430FR6047 Tool/software: Does TI have a support team/feature for reviewing schematics and PCB Layout? I have an Altium design that I was hoping to get reviewed.
View ArticleForum Post: RE: TMS320F2800135: Migration error from one IC to another with...
Hi, Did you follow this step in the FAQ to configure the default RAM linker command file? It doesn't seem the linker command file (syscfg/device_cmd.cmd) was properly generated. In the linker command...
View ArticleForum Post: RE: TMS320F28379D: XDS110 debug probe
Hi, Are you using a LaunchPad or controlCard? Please refer to the JTAG Connectivity Debug Guide , specifically Section 4.1 for debug steps: Best, Matt
View ArticleForum Post: RE: TMS320F280039C: After the EPWM module is configured, does...
Hi Zhen, Are you generating very basic PWM waveforms? If so, could you instead use eCAP to generate your waveform? There you'll have 2^32 max value for the TBPRD. Best, Ryan Ma
View ArticleForum Post: RE: ARM-CGT: What is the error code "#2710-D" about in ARM CGT?
One way to cause diagnostic 2710 to be emitted is to attempt to define std::initializer_list like so ... % type file.cpp // file.cpp namespace std { template class initializer_list {}; } % armcl...
View ArticleForum Post: RE: TMS320F28379D: LAUNCHXL-F28379D
Hello Kishor, Have you resolved the CAN issue?
View Article