Forum Post: RE: AM2632-Q1: CONTROLLER PART SUITABILITY FOR RAILWAY APPLICATION
[quote userid="593283"...
View ArticleForum Post: RE: TMS320F28388D: CLB to SPI CLK Connection – GPIO Usage
Hi Wilko, GPIO configuration is only necessary if you are using an external signal from a pin. You can override the SPI clock without any interaction from the GPIOs. Thank you, Luke
View ArticleForum Post: RE: TMS320F28P650DK: Problems connecting to device after programming
Also, interestingly, if I hold the TMS320F28P650DK in reset (hold the nXRS pin low), I am able to connect to the part using the 'test connection' function:- So I think the XDS200 is working fine?
View ArticleForum Post: RE: AM2632: Configuring EDMA for QSPI and UART
I turned off DMA for the QSPI in the sample project and the initial DMA serial write does work again. I'd be happy to zip up the project if that will help.
View ArticleForum Post: RE: AM263P4: Can XBAR be used to map ADC0_EVT1 to PRU_0 interrupt.
Hi Nathan, Could you please help me understand the issue on PRU side that you are facing?
View ArticleForum Post: RE: AM263P4: Secure Boot: individual calibration section flashing
[quote userid="640733"...
View ArticleForum Post: RE: AM263P4: Secure Boot: individual calibration section flashing
[quote userid="640733"...
View ArticleForum Post: RE: AM263P4: Secure Boot: individual calibration section flashing
[quote userid="640733"...
View ArticleForum Post: RE: AM263P4: Secure Boot: individual calibration section flashing
[quote userid="640733"...
View ArticleForum Post: RE: TMS320F28379D: Multicore system CLB Ownership and ISRs
Hi Prakhar, I am out of office until tomorrow, will test on my side when I return. Thank you, Luke
View ArticleForum Post: RE: AM263P4: Can XBAR be used to map ADC0_EVT1 to PRU_0 interrupt.
The issue is that the PRU is not receiving any type of signal across the Output XBAR that the ADC has completed its conversion. As documented above, the Output XBAR is being populated as expected when...
View ArticleForum Post: RE: TMS320F28377D: program stuck when the structure pointer is...
Hi Joe, Is there a specific example that you are referencing in C2000Ware? If not, what was the last version of CCS and the compiler this code last compiled successfully in? Can you provided more...
View ArticleForum Post: RE: LP-AM243: LP-AM243 ETHERNET/IP CODESYS EXAMPLES PROGRAM FOR...
Hi Thien, I have forwarded your question for further discussion; please expect some time for them to investigate the behavior you're seeing. Regards, Karam
View ArticleForum Post: TMS570LC4357: Using ePWM or N2HET to hold a specific duty cycle...
Part Number: TMS570LC4357 Tool/software: I have a LTC2644 DAC connected to shared ePWM/N2HET pin. I'd like to generate a low-frequency PWM output (50Hz) on that output with a duty cycle that can vary...
View ArticleForum Post: RE: MSP430FR6043: Using multiplexer and using at least 2 MSPs...
Hi Brian, If using 2 MSPs together and specifically theirs EVMs modules is an option, could you maybe confirm info from this old post...
View ArticleForum Post: RE: TMS320F28379D: CLA Loop unrolling injects unnecessary NOP...
I found a workaround. But I can only give a partial explanation for it. Add the restrict keyword to the definition of the pointers ... uint32_t * restrict dst = (uint32_t *)data_out; uint32_t *...
View ArticleForum Post: RE: TMS320F28388D: Optimization Behavior with -O4 in TI C2000...
[quote userid="650329"...
View ArticleForum Post: RE: TMS320F28379D: Timing related queries for QDC in EQEP module
Hi Prarambhik, 1. The logic inside the DSP to cause the QDC (Quadrature Direction Change) flag to become high when one signal goes missing is based on the quadrature decoder state machine. The...
View ArticleForum Post: RE: TMS320F2809: GPO electrical state after reset guaranteed zero?
Hi, [quote userid="164953" url="~/support/microcontrollers/c2000-microcontrollers-group/c2000/f/c2000-microcontrollers-forum/1500669/tms320f2809-gpo-electrical-state-after-reset-guaranteed-zero"]Above...
View ArticleForum Post: RE: TMS320F280039C: Using eCAP Block in HRCAP Mode to Capture...
Hi Ruhaizan, Unfortunately I do not have access to this matlab and do not have much experience using MatLAB. I will see if I can find someone who can help. Will you be able to instead run the hrcap...
View Article