Forum Post: RE: UNIFLASH: Flash the program using uniflash into our product...
Hi, Once you have your image.bin created in CCS you can then use uniflash to flash that image. I recommend follwowing chapter 6 of the uniflash guide. https://www.ti.com/lit/ug/swru469h/swru469h.pdf...
View ArticleForum Post: RE: TMS320F280025: tmdxiddk379d: ADC interrupt source on SOC0
Hi Hans, IU, IV, IW has different SOC. So, you should set interrupt accordingly when you want to trigger. Please do EOC of SOCx to collect the results. Thanks, Susmitha
View ArticleForum Post: RE: TMS320F28375D: How to continue supplying the SPI clock(SPICLK)
Hello, First, I am concerned about the event being described. That does not sound like typical behavior for a peripheral device. Please clarify what undesired behavior is being observed after the CLK...
View ArticleForum Post: RE: TMS320F28375D: How to continue supplying the SPI clock(SPICLK)
(continued) Second , there is no way to facilitate this based solely out of the SPI. My first thought was to use the CLB, as that would be an incredibly simple process, but unfortunately the indicated...
View ArticleForum Post: TMS320F28P550SJ: CLA fails to write to EPWM after Power Cycle
Part Number: TMS320F28P550SJ Other Parts Discussed in Thread: SYSCONFIG Tool/software: Hello, The title sums it up pretty well. After flashing, the CLA is able to write to the EPWM Counter Compare....
View ArticleForum Post: RE: LP-AM243: LP-AM243 ETHERNET/IP CODESYS EXAMPLES PROGRAM FOR...
Hi Kram. I checked at Debugging JTAG last night I could not find how to solve this problems. I need to solve this problems ASAP. Please point me to the right location to solve . Thanks again.
View ArticleForum Post: TMDSCNCD28379D: Renaming multi-cpu project
Part Number: TMDSCNCD28379D Other Parts Discussed in Thread: SYSCONFIG Tool/software: Hi, I would like to be able to create a project that could be run on two CPUs. There's "sci_ex2_sysconfig" example...
View ArticleForum Post: RE: AM2612: How to initialize PRU0 GPIO when link PRU_GPIO to...
As per our discussion, The pinmux config can be done via sysconfig. Let me know if you have any further questions.
View ArticleForum Post: RE: LP-AM261: SDK version 10.0.1.10 SBL OSPI example is not...
Hi Joshua, Please request for new LP.
View ArticleForum Post: RE: AM263P4: CLion IDE causing errors when updating core...
Hi Huey, Unfortunately, we could not reproduce the issue on our side. The register config is set in the architecture file itself, where as the base addess is provided in am263x.cfg file
View ArticleForum Post: RE: TMDSCNCD28379D: Renaming multi-cpu project
I should add what I mean by the 'simple debugging experience': I could use: Debug As -> 1 Code Composer Debug Session, from 'sci_ex2_sysconfig_multi', which builds and loads both project...
View ArticleForum Post: RE: AM263P4: CLion IDE causing errors when updating core...
What is the observation upon applying the CLion IDE support team response?
View ArticleForum Post: RE: AM2632: Configuring EDMA for QSPI and UART
Hi Tom, Does it work if you disable DMA in QSPI?
View ArticleForum Post: RE: TMS320F28335: trapezoidal control of bldc motor using...
Hello, Apologies for the delay in response, I was unexpectedly out of office. Because this thread appears to be a duplicate of the other one that I have now responded to (...
View ArticleForum Post: RE: TMS320F280039C: CLB clock setting
Hi Liu Liu, By default it is best to run the CLB Tile and register clocks at maximum speed unless you have some requirements that might benefit from modifying these clock frequencies. Thank you, Luke
View ArticleForum Post: RE: MCU-PLUS-SDK-AM261X: HSMRt firmware loading fails with AM261x...
Hi Joshua, Did you already programmed the keys? If yes is it the TI dummy keys or custom keys? Did you install TIFS and rebuild the HSMRT image? Did you rebuild the SBL OSPI with argument...
View ArticleForum Post: TMS320F28P650DK: Problems connecting to device after programming
Part Number: TMS320F28P650DK Tool/software: Dear Forum, I have developed some custom digital control boards based around the TMS320F28P650DK9ZEJ part. The prototype board I have been using for a few...
View ArticleForum Post: MSPM0L1306: Modify CTL0 SPI register value
Part Number: MSPM0L1306 Other Parts Discussed in Thread: TRF7960A , Tool/software: Hello, I am making a firmware for a MSPM0L1306 which controls a TRF7960A RFID reader. According to TRF7960A...
View ArticleForum Post: RE: TMS320F280039C: TMS320F280039C
Hello, Apologies for the delay, I unexpectedly out of office. This thread appears to be a duplicate of the other thread which I have now responded to (...
View ArticleForum Post: RE: AM2632-Q1: CONTROLLER PART SUITABILITY FOR RAILWAY APPLICATION
Hi Hemal, AM263Px is a successor part for AM263x with higher RAM size and OSPI controller which supports XIP.
View Article