Forum Post: MSPM0G3507: deadTimeCompute source code is not available
Part Number: MSPM0G3507 Tool/software: Hi there, I try to figure out all the details of "motor_control_pmsm_foc". But the source code of "deadTimeCompute" is not available. Is it possible that TI can...
View ArticleForum Post: RE: TMS320F280039C: After the EPWM module is configured, does...
Hi Ryan, From the tests, changes to CLKDIV take effect immediately, causing the actions of the current cycle to last longer. But the next cycle is the programmed action. If changes are not...
View ArticleForum Post: RE: TMS320F28388D: CAN Message objects configuration
Hi, this code written by my own i'm using C2000Ware_5_01_00_00, and CCS version 12.8.1 thanks,
View ArticleForum Post: RE: TMS320F28379D: Unable to observe XCLKOUT signal on GPIO24 via...
Thank you so much, Zackary! I had misunderstood the role of the Input XBAR — I assumed I could use it to route the internally generated XCLKOUT from GPIO73 back into the chip. As in the TRM, it is...
View ArticleForum Post: TMS320F280025: tmdxiddk379d: ADC interrupt source on SOC0
Part Number: TMS320F280025 Other Parts Discussed in Thread: TMDXIDDK379D Tool/software: Hi, I am using the MotorControl SDK 5.0.2 and there I had a look at the sensored_foc_f28002x project...
View ArticleForum Post: EVM430-FR6047: error #10010: errors encountered during linking;...
Part Number: EVM430-FR6047 Tool/software: Hello, I’m new to TI microcontrollers as well as the Code Composer Studio (CCS) IDE. I have downloaded the demo project for the EVM430-FR6047 from TI’s...
View ArticleForum Post: RE: MSPM0G3507-Q1: Questions about TIMx event and DMA transfer mode
Hi Pengfei, Thank you for the explanation. Now I wonder that if FSUB_x can be shared with 7ch PWMs' publisher. As I described, we should trigger the event for 7ch PWMs, but DMA seems only have two...
View ArticleForum Post: RE: LAUNCHXL-F28379D: ENOENT: no such file or directory, open
It's running after restarting the ccs... Thanks
View ArticleForum Post: RE: TMS320F280025: Memory Allocation
Hi Veena, Did you see my reply to your last reply to my question? I'm still waiting
View ArticleForum Post: RE: TMS320F28379D: Peripheral Initialization Dependencies
Hello Aishwarya, Thank you! Is your expert back to the office?
View ArticleForum Post: RE: TMS320F28069: Is it okay to leave SOC1 unconfigured when...
Hi Ben, Thanks again for your clarification earlier regarding the simultaneous sampling mode. Based on the description in the TRM, I understand that when simultaneous sampling is enabled (e.g.,...
View ArticleForum Post: TMDSCNCD28P55X: TMDSCNCD28P55X
Part Number: TMDSCNCD28P55X Other Parts Discussed in Thread: TIDA-010955 Tool/software: Hi, I was looking through this device's design guide and application in arc fault detection using embedded AI...
View ArticleForum Post: RE: TMS320F28379D: EnDat Clock Issue: No PWM on GPIO6, Code Hangs...
Hello, First of all, I would like to clarify that I am not unfamiliar with how to configure and run PWM on the TMS320F28379D. My current objective is to drive an encoder using the EnDat library, and I...
View ArticleForum Post: RE: F29H85X-SOM-EVM: RTINT on F29H85x
Emanuale, Thank you, I will also look into this further on my end and see if I can replicate the issue. Best Regards, Aishwarya
View ArticleForum Post: RE: AM2432: MCU-PLUS-SDK-AM243X: Cannot SBL_OSPI boot the hs_fs...
Hi Meet, first, the examples of ospi_flash_diag/dma/io can be run correctly with the sdk_mcu in ind_comms_ sdk_am243x_09_02_00_15 using the flash chip of IS25WX064. then, when using the sbl_ospi th...
View ArticleForum Post: TMS320F280049C: Can TMS320F28004x Generate Non-Complementary PWM...
Part Number: TMS320F280049C Tool/software: Hi, I would like to confirm whether it can support a specific PWM waveform. This capability is essential for determining whether the C2000 series is a...
View ArticleForum Post: RE: UCC25660: Variable range of output voltage in LLC topology...
Hi JCHK, Thank you for your reply! PMP23454 is very helpful. Conor
View ArticleForum Post: RE: AM2434: Power down sequencing
Hi Sreenivasa, The customer wants a clear answer from TI. "seems Ok" is not enough. Could you give me Yes or No? Thanks and regards, Koichiro Tashiro
View ArticleForum Post: TMS320F28P650SH: Peripheral Configuration
Part Number: TMS320F28P650SH Tool/software: Hi Support Team, I’m planning to use the F28P650SH6PTP, and I need some basic peripheral circuit design recommendations for it (such as: power supply,...
View ArticleForum Post: RE: TMS320F28379D: EnDat Clock Issue: No PWM on GPIO6, Code Hangs...
e2e.ti.com/.../endat_5F00_init.zip Please look at the code
View Article
