Forum Post: MSPM0G3507: Prevent TIMA1 event on re-enable
Part Number: MSPM0G3507 Tool/software: Hey. I am having an issue with some pwm timers - let me describe what I am doing: (forgive the long description - it's as short as I could make it). I am...
View ArticleForum Post: AM263P4-Q1: Is it possible to use GCC compiler instead of CLANG?
Part Number: AM263P4-Q1 Tool/software: Dear Champs, My customer is trying to use commercial gcc compiler to develop SW for AM263P. In this case, what is technical problem? Is there any issue to use...
View ArticleForum Post: RE: LP-AM243: MCAN Loopback Test (Interrupt) Extended Format...
What is wrong with my parameters?
View ArticleForum Post: RE: MSPM0G3519: MCAL_MSPM0_00.02.04.00
Hi, Okay, for the reprogram issue. You can try run a factory reset on the MCU and then try program the MCU again. e2e.ti.com/.../0160.Factory_5F00_reset_5F00_v3.pdf Best regards, Cash Hao
View ArticleForum Post: TMS320F28388D: Serial flash programmer run on Ubuntu (Linux)
Part Number: TMS320F28388D Tool/software: Hi I need run the serial flash programmer (C2000) app on Ubuntu OS. Does Ti support that? Brs, longpt
View ArticleForum Post: TMS320F28075: TMS320F28075:
Part Number: TMS320F28075 Tool/software: Hello, I get the following error message while debugging. It doesn't get cleared even if I remove all breakpoints. Let me know how to fix it. CPU1_CLA1:...
View ArticleForum Post: RE: LP-AM243: MCAN Loopback Test (Interrupt) Extended Format...
Hi Yoshki-San, Please allow me some more time to review the code and get back to you. Best Regards, Meet.
View ArticleForum Post: RE: AM2732: correct way to setting QSPI Boot in custom board with...
Hi, Daniel. I checked all binary in SI/SO. Result is shown below. ## Custom board | SI | SO | CMD | | ------ | ------ | --------- | | FF | FF | | | FF | FF | | | 55 | FF | | | 99 | FF | | | 05 | FF |...
View ArticleForum Post: RE: MSPM0G1105: Regarding the oscillation of an external ceramic...
Hi, It is not the thing written in the XD110 probe user's guide. Use LP for example, before power up the MCU, I remove the jumper on the NRST pin. It disconnect the conection between MCU and XDS-110...
View ArticleForum Post: RE: TMS320F28379D: SysConfig enabled project ?
Hi Paul Please find response to your queries below 1. A CCS project becomes SysConfig enabled if you add any file with .syscfg extension to the project. In this case, the file...
View ArticleForum Post: RE: MSPM0G3519: MSPM0G3519 Reading GPIO through API
Hi, I am not exactly getting your point. But for a current draw of 70mA on a single pin. It could damage that pin with this high current. The maximum current on a SDIO is only 6mA. That GPIO could be...
View ArticleForum Post: RE: LP-AM243: MCAN Loopback Test (Interrupt) Extended Format...
mcan_loopback_interrupt.c sets the following structures MCAN_InitParams MCAN_ConfigParams MCAN_MsgRAMConfigParams MCAN_StdMsgIDFilterElement MCAN_ExtMsgIDFilterElement MCAN_BitTimingParams...
View ArticleForum Post: MSPM0G3507: Change Secondary BSL start address
Part Number: MSPM0G3507 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Hello Now, I try to use secondary BSL, and I'd like to change start address. There is example about change start...
View ArticleForum Post: AM2634: UART blocking sdk 10.1 not working propperly
Part Number: AM2634 Tool/software: Hi The UART driver from sdk10.1 does not works well with XMODEM (from the drivers/bootloader), it worked ok in the sdk9.2 version. UART is in blocking mode. What...
View ArticleForum Post: RE: MSPM0G3507: what is the MAX eRPM when use MSPM0G3507+FOC
Hi Nan, Sorry, I am not the expert on C2000 device. I recommend you file a new thread in C2000 forum. B.R. Sal
View ArticleForum Post: RE: AM263P4: EPWMs out of sync by 1 clock cycle
I think this is a recognised (but not well documented) phenomenon. I found the following in C:\ti\mcu_plus_sdk_am263px_10_01_00_34\examples\drivers\epwm\epwm_synchronization\epwm_synchronization.c /*...
View ArticleForum Post: RE: MSPM0G1105: Regarding the oscillation of an external ceramic...
Hi Cash, Thank you for your explanation so many times. In terms of hardware connection, does that mean that NRST must be separated between the XDS110 and the target MCU? To be precise, what I'm using...
View ArticleForum Post: RE: TMS320F2800137: DAC NOT CONFIGURING PROPERLY
Kindly please help me through it
View ArticleForum Post: TMS320F28388S: MCU products with a library containing SNMP agent...
Part Number: TMS320F28388S Tool/software: I would like to know which MCUs in the TI portfolio, not just the c2000, have a library that includes an SNMP agent v2c or v3 example. There is a requirement...
View ArticleForum Post: RE: TMS320F28384S: Inquiry about Required Code Modifications in...
Conor Are you using the Sysconfig generated code? If so, then you can look at Board_init() function to see the GPIO configuration. You can also look at the USBGPIOEnable() function in the usb_hal.c...
View Article