Forum Post: MSPM0G3507: why is there no IDDrun using 32KHz xtal in this chart...
Part Number: MSPM0G3507 Tool/software: I have yet to find a single TI written reference for what MSPM0 power should be in low power RUNNING mode, ie running from 32767Hz Xtal. Where can I find that...
View ArticleForum Post: RE: MSPBSL: BSL Scripter with Ethernet not working
[quote userid="577647"...
View ArticleForum Post: RE: F29H85X-SOM-EVM: F29H85X controlSOM evaluation board Failed...
Do you have any other suggestions for me? Do I need to change any other settings or resistors on the board?
View ArticleForum Post: RE: TMS320F280038C-Q1: Pull-up or pull-down of ERRORSTS pin
Hello Seungeun, The ERRORSTS pin stays in a tri-state until the chip's power rails hit the lower operational limit. Since the ERRORSTS pin is active-low by default, if you want to keep an eye on its...
View ArticleForum Post: LAUNCHXL-F2800157: Error -260 with XDS110 Debugger on...
Part Number: LAUNCHXL-F2800157 Tool/software: Hello We are experiencing a connection issue with our LAUNCHXL-F2800157 LaunchPad. During an active debug session, We inadvertently disconnected the...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM263PX: CAN Communication & Model Deployment.
Rutwij, [quote userid="644929"...
View ArticleForum Post: RE: MSPM0L1106: UniFlash with error : Data Block Size less than...
Hi Alan, This seems to be an alignment issue. I would recommend to check your linker file (.cmd,) and make sure you are using the palign command. You can follow the image bellow as an example: Best...
View ArticleForum Post: RE: MSPM0C1104: Issue with MSPM0C1104 – Program Jumps to...
Based on your traceback, another way of describing this would be an "unexpected Reset". There's quite a lot going on in your .syscfg, which I probably couldn't reconstruct. It would be informative if...
View ArticleForum Post: RE: AM263P4: Scripts for OSPI flash of AM263PX
Hi Vishwanath, Thank you for the reply. Please allow me to come back on this by mid of next week after discussing with the OSPI SW experts /MCAL team. Thanks & Regards, Rijohn
View ArticleForum Post: TMS320F2812: c2000 compiler issue
Part Number: TMS320F2812 Tool/software: Hello, For my projet for Safran Landing System, we are currently using the microcontroller TMS320F2812. This microcontroller uses the compiler C2000 generation...
View ArticleForum Post: RE: MSPM0G3507: BUG REPORT - Energy trace battery life data...
Hi Chris, This is a known issue that was fixed in CCS 20.1.0: https://sir.ext.ti.com/jira/browse/EXT_EP-12165 Thanks ki
View ArticleForum Post: RE: TMS320F280039C: Error connecting to target (Error -1135 @ 0x0)
Hello, You can refer to the F28003x TRM : The default boot mode select pins can be configured via S3 on the LaunchPad. Set GPIO24 = 0 and GPIO32 = 1 to configure the device for Wait Boot. Best, Matt
View ArticleForum Post: RE: MSP430FR2675: Slider Sensitivity Issue
Hi Pallavi, My recommendation is to increase the sensitivity (change the conversion count to a maximum of 800). Also, are there any grounds near the sliders? What kind of ground are you using (solid...
View ArticleForum Post: RE: TMDSHVMTRINSPIN: shoot through protection circuit in single IC
maybe you should switch a C2000 MCU here is an example of a gate driver with this feature https://www.ti.com/product/UCC27712-Q1
View ArticleForum Post: EVM430-FR6047: Measuring power consumption
Part Number: EVM430-FR6047 Other Parts Discussed in Thread: TIDA-01486 , MSP430FR6047 Tool/software: We are evaluating the MSP430FR6047 system for water flow measurement using transducers that are...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: AM243x LaunchPad - Ethernet/IP adapter...
Hi, Is there a way to use two different read/write commands regarding flash with OSPI controller? My goal is use two different read/write commands, one for reading/writing one section of...
View ArticleForum Post: RE: TMDS243EVM: Where can I get "DDR SUBSYSTEM REGISTER...
did you follow the url in the instructions? Regards, James
View ArticleForum Post: RE: TMS320F28379S: C28xx_CPU1: Error during Flash verification....
Hello Matthew, When do you think the person that is more familiar with the DCSM will be available to help fix this issue? Thanks, Stephen
View ArticleForum Post: RE: MSPM0G3507: Configuration for max ADC throughput
i took the sample ping pong and modified it very slightly (speed, which channel) i ran it, hit 2 break points (filling first ping then pong) then copied the values out of the debugger and pasted them...
View ArticleForum Post: RE: TM4C129ENCPDT: Project was working, and now I keep jumping to...
Charels, Thank you for suggesting these posts, and I will review these. No, the project is not exactly like the tcpEcho function. Let me provide you with more details. First, here is main: int32_t...
View Article