Forum Post: MSP430FR5969: Understanding the I2C Master Transmitter Mode picture
Part Number: MSP430FR5969 Tool/software: All, I am trying to wrap my head around this diagram. I don't quite understand what is going on, especially the different arrows pointing up and down. Trying...
View ArticleForum Post: RE: LAUNCHXL-F2800157: Erase flash memory
using debug view in ccs studio Thnaks
View ArticleForum Post: MSP-GANG: Error 23: MCU device initialization failed
Part Number: MSP-GANG Other Parts Discussed in Thread: MSPM0L1305 Tool/software: First, we can check our target PCBA is ok, when we use the J-link tool to be programmed it can be successful. But when...
View ArticleForum Post: RE: EVM430-FR6043: With the evaluation board using 200kHz sensors...
HI Vishnu, It seems that you are trying to measure the thickness of plastic. This gas meter reference design is not designed for your application. I do not think a valid signal can be received on the...
View ArticleForum Post: TMS320F2800135: Sysconfig build error
Part Number: TMS320F2800135 Other Parts Discussed in Thread: C2000WARE , SYSCONFIG Tool/software: Invalid argument '--product': No product with name "C2000WARE" and version "5.04.00.00" found The...
View ArticleForum Post: RE: MSPBSL: BSL Scripter with Ethernet not working
Hello Charles, I connected 192.168.254.3 and didnt connect 10.169.227.26(office LAN). It got flashed as expected. But the problem is i have to reset the MCU everytime i run the script. If i dont reset...
View ArticleForum Post: RE: LP-AM243: MCAN Loopback Test (Interrupt) Extended Format...
Thanks. Can communication is serial communication. I thought I could just connect tx=>rx, rx=>tx like uart. But this was a mistake....
View ArticleForum Post: RE: EVM430-FR6043: With the evaluation board using 200kHz sensors...
Hi Cash, I am not trying to measure the thickness of the plastic material; instead, I am verifying whether the sensors are capable of transmitting signals through the plastic material. Thank you...
View ArticleForum Post: MSPM0G3507: Interrupt fires instantly when enabled
Part Number: MSPM0G3507 Tool/software: Hey. I am trying to synchronize some control logic in my code to the CCD1 event of TIMA1. So I am running a function where I enable this interrupt: static inline...
View ArticleForum Post: RE: EVM430-FR6043: Measurement of a 1-meter diameter gas pipe...
Hi, I would recommend you to try with the second approach for your application. And for this 1 meter gas pipe, do you mean the distance between transducers would 1 meter? Best regards, Cash Hao
View ArticleForum Post: RE: MSPM0L1106: Single line UART communication
When Rx pin is configured to UART Rx mode, if the line is low, then Rx received the 0x00 because low level means a new start. So maybe you can check the line level. Only when the level is high will...
View ArticleForum Post: RE: MSPM0L1106: Flash memory reservation
Please note there should not be any overlay on FLASH area. For example, FLASH (RX) : origin = 0x00000000, length = 0x0000FFF8, means it contains FLASH from 0x0000 to 0xFFF8.
View ArticleForum Post: LAUNCHXL2-570LC43: Garbage string data to the Tera term
Part Number: LAUNCHXL2-570LC43 Tool/software: Hello, This is JJ I tried to read the data using tera term with sci1 port in LAUNCHXL2-570LC43. This is tera term settings, Basically, the other data seem...
View ArticleForum Post: RE: MSP430FR5970: MSP430 Pinmux assignment and MCU Programming.
From my side the schematic looks good. A debugger/programmer is necessary to program the code to the MCU. If you are not familiar with this device at all, maybe you can start with our EVM first, which...
View ArticleForum Post: RE: MSPM0G3507: Timer Settings - TRM Confirmation
Hi Kenley, No. the zero pulse just mean that the counter has counted for one cycle. Since it is a 16 bit timer in up counting mode. When the counter counts up to 65535(2^16-1). The next count will be...
View ArticleForum Post: RE: MSPM0G3507: No debug-play button after updating
That's actually what I tried to describe above. For example, I make a new simple project, using the "empty_driverlib_src" template. I enable "DriverLib" in the system configurator. save all, rebuild,...
View ArticleForum Post: AM2634-Q1: S25FL128L flash compability
Part Number: AM2634-Q1 Tool/software: Hi team, is the S25FL128 L also a compatible flash device for the AM2634-Q1? In the flash compability guide only the S25FL128 S is listed. If the device is...
View ArticleForum Post: RE: EVM430-FR6043: With the evaluation board using 200kHz sensors...
Hi, Get it. But I am afraid not. Best regards, Cash Hao
View ArticleForum Post: RE: TMS320F280039: The first pulse of EPWM appears to be...
Hi Allison, Yes, after I set it to "immediate load", there is no case of a high level at the same time. This is because in TBPRD shadow loading, TBPRD = 0, TBCTR = 0, for EPWMA,...
View Article