Forum Post: TMDS243EVM: Configure EtherCAT and standard ethernet based on...
Part Number: TMDS243EVM Tool/software: we designed a new board based on INDUSTRIAL COMM SDK(ind_comms_sdk_am243x_09_02_00_15), which have 4 RJ45 ports, two are used for EtherCAT(IN and OUT), the other...
View ArticleForum Post: RE: MSPM0L1106: Flash memory reservation
Hi Yuhao, Thank you for your support. I found that there is one .cmd file in my project folder, device_linker.cmd, under directory, \Debug\syscfg\. It seems that it is a generated file from CCS. Where...
View ArticleForum Post: RE: AM2432: How to Apply IPC Demo on Customer CCS Project
Our project is built base on the CCS12.8.1, and It's difficult for us to port our project code on top of the IPC demo. So could you please let us know how to create an ipc_notify_echo base on our...
View ArticleForum Post: MSPM0G3507: How do I get it to run at the spec 96ua/MHz?
Part Number: MSPM0G3507 Other Parts Discussed in Thread: MSP430F1232 , Tool/software: Spec says it will run at 96ua/MHZ so using 32K clock should be able to run CPU in run mode at about 3 uA, yes? I...
View ArticleForum Post: RE: MSPM0G3507: Configuration for max ADC throughput
Hi WorkerBee, I think you descript clearly about your issues. For the primary issue, sorry I have no idea about why the result get the mis order currently. So if you could give more information about...
View ArticleForum Post: RE: MSP430F1232: Does any microcontroller of MSP430 family...
Link Similar thread here: (+) MSP430AFE231: Does any microcontroller of MSP430 family support CAN protocol ? - MSP low-power microcontroller forum - MSP low-power microcontrollers - TI E2E support...
View ArticleForum Post: RE: MSPM0L1106: Flash memory reservation
Hi Yuhao, Furthermore, the following is my proposed modification. Will this cause any overlap error with FLASH? MEMORY { FLASH (RX) : origin = 0x00000000, length = 0x0000FFF8 SRAM (RWX) : origin =...
View ArticleForum Post: TMDS243EVM: Is there a problem if MII0_RXLINK signal is not...
Part Number: TMDS243EVM Tool/software: Is there a problem if MII0_RXLINK signal is not configured? because not all the PHY chips support this signal.
View ArticleForum Post: RE: MSPM0L BSL I2C Adress Clarification
It is a 7 bit I2C address. you will see 1001 000x on the bus.
View ArticleForum Post: MSPM0G3507: Can't access the e2e.ti.com write site from my office...
Part Number: MSPM0G3507 Tool/software: I am having problems access ti.e2e.com. I get access denied when using office internet which has static ip. Switch to phone and disable wifi and it works which...
View ArticleForum Post: TMDS243EVM: Is WR_PROTECT effective at 0 or 1? Is SD_DETECT...
Part Number: TMDS243EVM Tool/software: Is WR_PROTECT effective at 0 or 1? Is SD_DETECT effective with 0 or 1?
View ArticleForum Post: RE: MSPM0L1106: Flash memory reservation
To modify the cmd file manually, first you need to copy the cmd file to the project. Then please disable the cmd generation in SysConfig.
View ArticleForum Post: RE: MSPM0L1106: Single line UART communication
Hi Yuhao, Thank you for your support. Due to external circuit requirement, the logic should keep low when there is no data communication. For testing purpose, I tried to set Tx pin to input without...
View ArticleForum Post: RE: MSPM0G3507: CCS Theia ctrl-click on function goes to wrong...
Of course I can manually delete the .out file or add a prebuild step to do it automatically. But thats not the point. If build fails it should not even ASK if you want to debug the failed build which.
View ArticleForum Post: RE: MSPM0G3507: CCS Theia ctrl-click on function goes to wrong...
Any progress on a fix for the original topic of this post? This is a very dangerous and annoying problem for me. I am in project a and I need to modify function and ctrl-click takes me to same...
View ArticleForum Post: RE: MSPM0L1306: Enable UART RTFG timeout interrupt for DMA transfers
What you observed follows the spec. The FIFO will be transfer immediately via DMA. In fact DMA is suitable for certain length comms.
View ArticleForum Post: RE: MSPM0G3507: Duty cycle of first pwm period using shadow compare?
Hi, I do observe this behavior on my side. The issue is gone when I set the CC value again after enabling shadow function. No need to set load value again here. So, the current solution would be set...
View ArticleForum Post: RE: MSPM0L1106: Flash memory reservation
Hi Yuhao, After the changes, I got the overlap error as my expected. Can you suggest how to modify the .cmd file? AlanC.
View ArticleForum Post: RE: MSPM0G1107: (Error -6305) PRSC module failed to write to a...
Hi, Try pull the NRST pin to LOW before powering up the MCU. Then power up the MCU under this condition. Start a Factory Reset process and try again. Holding the NRST pin to LOW would force the MCU...
View ArticleForum Post: RE: C2000-GANG: Error 354 occurs when using C2000-GANG to batch...
I know the reason , it is our company ' s IT part that encrypts the file , which makes it unreadable
View Article