Forum Post: RE: MCU-PLUS-SDK-AM243X: Bootloader From DFU Tool
[quote userid="611267"...
View ArticleForum Post: RE: TMS320F28335: Programming a CSM password with UniFlash bricks...
Thanks for the tip I changed the boot mode to "Branch to check boot mode" and was able to unlock the chip.
View ArticleForum Post: RE: TMS320F28377D: TMS320F28377D
Thank you for your help. We have setup the tool to XDS200 and we can program the DSP. Regards, Joel.
View ArticleForum Post: RE: TDA4AL-Q1 cannot boot up at -40 degree C
Hi, Kevin Kuo & Luc I need to clarify something. Question 1 : I assume these 5 (parameter) experiments are works in normal temperature, isn't? 1. DDR config tool 0.10 + custom ddr timing setting +...
View ArticleForum Post: MSPM0G3107-Q1: MSPM0G3107 RTC seems stuck in BCD mode
Part Number: MSPM0G3107-Q1 Other Parts Discussed in Thread: MSPM0G3107 , SYSCONFIG Tool/software: First things first: The Errata for the MSPM0G3107 (SLAZ742A; checked version dating october 2023) does...
View ArticleForum Post: RE: RM44L520: GIOB[2] does not appear to be available as an...
We can do a live session -- how do you want to do this? Scott
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: Calculate CRC of sections with MCRC and...
Hello Andrea Politano, I am looking at the your queries and you may expect reply in one or two days . Regards, Anil.
View ArticleForum Post: RE: LAUNCHXL-F280039C: Launchpad debugger not responding
To confirm the issue, the customer can just try the workaround of plugging in the USB cable while S1 is being held down. If the XDS110 is detected after that, then it is the same exact issue. I am 99%...
View ArticleForum Post: RE: TIDM-02000: Query Regarding Slope Compensation in 3kW DC/DC...
Hello, I am working with Abdur. I have one question. See the isseued waveform, time is over 50% duty. If Duty time is near the 50% duty, Is there a way to force PWM off? Regards, Sangmo Kim.
View ArticleForum Post: RE: TMS320F2800137: Flash Erase Issue in 137
Hello Rajeshwary, Any feedback on above query?
View ArticleForum Post: RE: SAFETI-HALCOGEN-CSP: Safety Caseis not included in the CSP...
Hello Jagadish, Is there a time estimation for this request. It is a little urgent on our side at the moment. Thx
View ArticleForum Post: RE: TIDM-02000: Query Regarding Slope Compensation in 3kW DC/DC...
Hello, I checked CMPSS TRIPOUT signal again. Below waveform is measured when output load is fixed. Output voltage is operating normal, than suddenly happened peak voltage. When happened peak voltage,...
View ArticleForum Post: RE: AM2632: [Application] Flash code via LIN bus
Lin, Let me re-phrase: Flashing the device via LIN is possible, but is not supported by TI and there are no plans to do this. You can enable this by modifying the sbl_uart_uniflash file found at...
View ArticleForum Post: RE: LAUNCHXL-F28379D: Abnormal heating up issues
Hmm, I see. For current sensing we are using the TMCS1133 which takes power from the launchpad. I do not use any clamping or op-amps. Best, Ibrahim
View ArticleForum Post: RE: AM263P4: JTAG Clock Buffer on EVM
Hi Nishka, Can you refer me to the document where this requirement is shown? It will help give me context. Regards, Brennan
View ArticleForum Post: RE: MSP430F5359: CGT-generated MSP430X images won't start if .bss...
On my way to trying to collect more debugging data, I moved my hardware initialization code into a _system_pre_init() routine that I just wrote (and made that routine return 1 indicating success)....
View ArticleForum Post: MSP430AFE232: Windows 11
Part Number: MSP430AFE232 Other Parts Discussed in Thread: UNIFLASH Tool/software: Does UNIFLASH Version: 9.0.0 Release date: 20 Dec 2024, support windows 11 ??
View ArticleForum Post: RE: MSP430F5359: CGT-generated MSP430X images won't start if .bss...
I'm thinking the problem is actually the Watch Dog Timer. The big difference that my re-arrangement made was that _system_pre_init() now sets the WDT to Hold Mode whereas my old code was causing the...
View ArticleForum Post: RE: LP-AM263P: MCAN
Arjun, From a HW perspective, everything looks to be ok - especially since you say that this configuration worked with the old part number. I am going to check the SDK example history to see if any of...
View ArticleForum Post: RE: MSPM0G1507: BCR configuration to disable SWD and BSL...
Hi Zhuang, I will recommend posting this question as a different E2E thread. Best Regards, Diego Abad
View Article