Forum Post: RE: F28M35M52C: Flash Programming fails while CSM is active
Hi Keith, It seems like you've allocated some resources to S0 and S1 SHRAM, which are non secure memories. Could you try allocating everything to the securable RAMs (C0 and C1)? Thank you, Luke
View ArticleForum Post: RE: TMS320F280025C: "if A
Thank you for submitting a test case. To explore ... [quote userid="449244"...
View ArticleForum Post: RE: TMS320F28027: PWM and HWPWM Max resolution
Hi Adam, Thanks for the context. And let me know if you have other questions. Best Regards, Allison
View ArticleForum Post: RE: TMS320F28374D: Control for both Duty Cycle and Phase shift
Hi Eric, Just responding here to state we are following up via email. We can post again if further information should be provided on the thread. Best Regards, Allison
View ArticleForum Post: RE: TMS320F280025C: Question about temperature cycle test of the...
Hi Julia, The device is powered on during our quality temperature cycle test. Other information can be found the device quality and reliability page which is linked for each part. You can find the...
View ArticleForum Post: RE: TMS320F28377S: spi and dma receive stuck
Hello, I apologize for my delayed response; I am still catching up on everything since the holidays. Is the issue still open? If so, please let me know and I will look in depth into your...
View ArticleForum Post: TMS570LC4357: PINMMR171 - Mismatch between CCS memory browser and...
Tool/software: Inconsistency between CCS 6 Memory Browser MCU TRM (SPNU563A) detected. The CCS memory browser shows the following information (data taken from image shown below): PINMMR171 Size: 20...
View ArticleForum Post: RE: AM263P4: When MCSPI5 is selected in SYSCONFIG, no code is...
Any replies to this item?
View ArticleForum Post: RE: TMS320F28388D: IPC Communication Method Between CM and CPU1...
I wrote the code based on the f2838x_cm_echoback_solution and f2838x_cpu1_allocate_ecat_to_cm examples. I also changed the configuration to FLASH [Active] under General >> Configuration in the...
View ArticleForum Post: RE: LAUNCHXL-F280049C:Unable to Receive Data on Slave...
Hi Daichi, Apologies for the delay. Please see my answers below: [quote userid="610452"...
View ArticleForum Post: RE: MSPM0L2228: SPI master receive not working for clock > 2MHz
Hi, SPI_STAT.BUSY is at the 5th bit. So, SPI bus is idle when STAT is 0x0F. For high speed SPI, interrupt can't be used. If SPI_SCLK is 16MHz then there are only a few instruction cycles to read each...
View ArticleForum Post: RE: TMS320F280025C: "if A
Hi George, Thanks a lot for your reply. Please see below: 1. could you elaborate "how to add the build option --src_interlist " to keep .asm file? 2. What can I do to shorten the execution time? Quentin
View ArticleForum Post: TMS320F28P650SH: VSSOSC pin connect
Part Number: TMS320F28P650SH Tool/software: the datasheet says，Crystal oscillator (X1 and X2) ground pin. When using an external crystal, do not connect this pin to the board ground. Instead, connect...
View ArticleForum Post: TMS320F280039: TIDM-02000, Why PWM can not be turn off when Main...
Part Number: TMS320F280039 Tool/software: Hello. I develop PSFB DCDC converter using TIDM 02000. When I am testing Peak load, I checked Main Transformer 1st current OCP. As tou can see below picture,...
View ArticleForum Post: AM263P4: watchdog interrupt example issue
Part Number: AM263P4 Other Parts Discussed in Thread: SYSCONFIG , TMDSCNCD263P Tool/software: Hi, My customer evaluates AM263P4 with below environment. CCS 12.8.1 SDK 10.1.0.31 Sysconfig 1.22.0 Board...
View ArticleForum Post: RE: TMS320F2800137: Questions about D/Q aixs current decoupling...
1. For my application, motor para. with Ld=Lq= 0.001H, Rs = 0.25Ω，4 paris PMSM, Rated voltage 360VDC, max 11000rpm Let's see the decoupling item for Vd: -speed_rps * objUser->motor_Ls_q_H *...
View ArticleForum Post: RE: C2000-GANG: C2000-GANG supported are C2000 Generation3?
Hi Charles, TMS320F28P65x devices are supported? Thank you for your support. Ronnakorn.
View ArticleForum Post: RE: AM2732: When the Ethernet framework based on lwip is added,...
Without changing the original udp server demo code, I modified the makefile and the lwipopts.h header to get the memory optimization shown in the figure. Is there any way to further optimize the...
View ArticleForum Post: RE: TM4C1294NCPDT: CODE FOR TM4C1294NCPDT (RTC CONFIGURATION CODE)
okay .. Thank you so much
View ArticleForum Post: RE: TMS320F280038C-Q1: Acknowledge Specific PIE Vector on driver...
Hi Gokhan, Each ACK only correlates to a specific ePIE group. There are no ACKs for individual interrupts inside groups. Each time an ISR is branched to, the ACK for the entire group will be "opened"...
View Article
