Forum Post: RE: MSP430FR6047: Not receiving clean downstream signal for clamp...
Hi Cash, Thank you for getting back to me. Happy New year! The differentiation to the set up here compared to clamp on app note is they are in V configuration vs direct path with transducers in the...
View ArticleForum Post: RE: TMS320F280039C: always can error at import sample of Mcan or can
Hi, Can you change the MCAN CLK DIV to a value which generates CAN clock frequency which is factor of CM clock frequency, for eg 5, which generates CAN clock of 20 MHz? regards, Anand
View ArticleForum Post: RE: TMS320F28374S: CS2619666 TMS320F28374S: Debug Error with...
Hi Cheng, Understood, like mentioned previously, there may be some system-level issue in your code which is independent of the compiler and would require testing/evaluation of project files. This...
View ArticleForum Post: RE: AM263P4-Q1: MATLAB integration with Code composer d
Nothing is attached. What errors do you get? Did you add any .h files?
View ArticleForum Post: RE: AM2634: Inaccessible memory addresses on HS-SE board causes...
Hi Riccardo, Sure no issues. Let me know in that case a call would be better and we can discuss over call on all open items. Best Regards, Shiv
View ArticleForum Post: RE: CODECOMPOSER: No GCC examples?
[quote userid="579788" url="~/support/microcontrollers/msp-low-power-microcontrollers-group/msp430/f/msp-low-power-microcontroller-forum/1454423/codecomposer-no-gcc-examples/5597024#5597024"]And this...
View ArticleForum Post: RE: AM2634: Is it possible to download code into AM2634 by using...
Hi Brennan, I am able to build example for Core 1. I am using below example code from resource explorer.
View ArticleForum Post: RE: LP-MSPM0G3507: Real time Debugging Issues with Application Board
Hi Piyush, The MSPM0G3507 doesn't support a 230VAC input. The maximum ADC input it supports is VDD. Are you using an isolation scheme or directly applying the 230VAC to the pins? Best Regards, Diego...
View ArticleForum Post: RE: MSP432E401Y: USB Bootloader
Hi, No, we do not have a USB bootloader with RTOS application. However, this post will be helpful with TI-RTOS examples and tips from Chester on bootloader with TI-RTOS application....
View ArticleForum Post: RE: TMS320F2800157: NOT ABLE TO ACHIEVE THE MAXIMUM SPEED IN...
Hello Yanming Luo, 1. Actually we are supplying the dc bus voltage based on the rated voltage of the motor. 2. Without altering the current vector angle, if I use the default current angle generated...
View ArticleForum Post: RE: TMS470MF03107: S4MF03107SPZQQ1R
Hi Jialing, Can you request CPR again and explain that you have already done the ABA swap and also verify the voltage and impedance compared with reference board and unit as asked in the email you...
View ArticleForum Post: RE: AM2634: Is it possible to download code into AM2634 by using...
Ajit, Please let me know the following information, and I will attempt to replicate your setup: CCS version AM263x MCU+ SDK version EVM and revision Have you tried uploading the code using the...
View ArticleForum Post: LAUNCHXL-F28379D: Error while launching debug session
Part Number: LAUNCHXL-F28379D Tool/software: Hi, I get an initialization error when I try to launch the debug session. The error message says, Debugger Initialization Error Can't generate board data...
View ArticleForum Post: RE: LP-MSPM0G3507: Real time Debugging Issues with Application Board
I assume he means his application hardware. I would see if there is a ground loop between the hardware and the debugging PC. You might need a USB isolator for safety reasons. (Or use a laptop that is...
View ArticleForum Post: RE: LAUNCHXL-F280049C: EPWM_setDeadBandDelayPolarity
Hi Andres, Those two functions will cause the DBCTL.POLSEL to be 0x1. EPWM_DB_POLARITY_ACTIVE_HIGH is the default behavior. Best, Ryan Ma
View ArticleForum Post: RE: TMS320F28388S: Some qustion about the demo:...
Hi Shuqing, 1. Yes this example will meet the customer's needs. 2. This seems like a bug in the example. EPWM1A and EPWM1B should have the same period. 3. This is expected due to the error in the...
View ArticleForum Post: RE: TMS320F28388S: INTM and DINT Functionality
Hi Delaney, How do I direct message you? Thank you, Ed
View ArticleForum Post: RE: MSPM0G1105: How to set GPIO pull-up/pull-down resistors
It is *mentioned* in the manual, but it is often easier to let the TI engineers wade through and figure it out, and use SysConfig to reap the fruits of their labours. Though I have found bugs in...
View Article