Forum Post: TMS320F28335: CCS FFT
Part Number: TMS320F28335 Tool/software: I used CCS7.4 to debug the data acquisition program in DMA mode. The collected data was stored in array A[256], and the odd points (left channel) in A were...
View ArticleForum Post: RE: TMS320F280039C: Look into the result of a macro after code...
Hi Ryan, Do you have any update?
View ArticleForum Post: RE: TMS320F28P550SJ: Use PGA as a buffer for ADC measurement
Hi Hadi and/or champs, This is urgent. Do you have any update? Is there anything wrong with Sysconfig or the datasheet? For Q5 above, In Sysconfig, How does the user change the ground pin to VSSA? How...
View ArticleForum Post: MSP432E401Y: MSP432E401Y SSIDATAGET() delay
Part Number: MSP432E401Y Tool/software: Hi Masters, I am reading data from an ADC with the following code. SSIConfigSetExpClk(SSI0_BASE, systemClock, SSI_FRF_MOTO_MODE_0, SSI_MODE_MASTER, 30000000,...
View ArticleForum Post: RE: MSP-EXP430G2ET: I am stuck in the "cloud" version of CCSTUDIO
Thanks Gary - Are you saying that I must got through the "Debug" step - even if the program compiled successfully? Does the "desktop" version of CCSTUDIO require the same? Thanks, ~S
View ArticleForum Post: RE: MSP430F2418: inquiry for operation voltage and clock.
Hi 2.7V drop occurs, but the MCU reset phenomenon does not always occur. MCU reset occurs very rarely. Sometimes it drops to around 2.5V. I hope know if 2.7V or 2.5V drop phenomenon is related to MCU...
View ArticleForum Post: RE: MSPM0G3507: Hall SENSORED FOC Guide not found
Hi Pengfei, Thanks for the information and support! Regards, Deven.
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: Writing to DDR when ECC is enabled
Hi Nihar Potturu, I understood your current comment about not being able to write after the DDR_inlineECCCfg function. But if I enable it after writing, the written value is cleared. What is the...
View ArticleForum Post: RE: TIEVM-HV-1PH-DCAC: TIDM-HV-1PH-DCAC
Amir, 1. can you respond to my other questions please - please refer to my other post. 2. You refer to pmp23069 - do you mean I have a hardware limit because of the FETs only? or the whole solution...
View ArticleForum Post: RE: AM2431: Ethernet performance
Hi Ashwani, PC is sending specific frames, need to be consumed by specific AM243x? The PC, which acts as the controller, sends different frames for various purposes. I can send MAC frames, and it...
View ArticleForum Post: AM2432: AM2432: ADC interrupt suddenly fail to trigger
Part Number: AM2432 Tool/software: Hello: When we use adc, there is a problem of occasional interruption loss. Please help us check it: 1. We trigger adc (one-shot mode) in pwm interrupt with pwm...
View ArticleForum Post: RE: TMS320F28375S: Issue with SPI Data Reception for SSI on...
Hello Allison, [quote userid="568270"...
View ArticleForum Post: RE: LAUNCHXL-F28379D: Assistance Required with Comparator Module...
Hi Peter Can you refer some example codes to achieve this functionality. Best regards, Tasmiya
View ArticleForum Post: RE: AM2431: Trying to output MCU_HFOSC0_CLK on MCU_SPI0_CS1
Hi Jeff, [quote userid="558363"...
View ArticleForum Post: TM4C123GH6PM: Dereferencing void *intfPtr on TivaC platform
Part Number: TM4C123GH6PM Tool/software: Hello, I am porting bmm350 sensor code to Tiva-C platform. https://github.com/boschsensortec/BMM350_SensorAPI The authors took advantage of function pointers...
View ArticleForum Post: RE: TIEVM-HV-1PH-DCAC: TIDM-HV-1PH-DCAC
Hello Tomer For Question 1, Can you please share the image of expression window when the trip occurs? Also, share the image of oscilloscope at the trip by triggering at a high current value. I need to...
View ArticleForum Post: RE: TIDM-HV-1PH-DCAC: Type of current controller referred to in...
Hello Abayomi sorry for delay. I took me some time to confirm that this indeed works as a PI controller. Thank you Amir Hussain
View ArticleForum Post: RE: TIDM-HV-1PH-DCAC: computeDF22_PRcontrollerCoeff() code
Hello Tomomi Thanks for pointing out the potential error in the implementation. Manish does not work with TI anymore and I have not got a chance to verify it yet as I am focusing on a different...
View ArticleForum Post: RE: TIDM-HV-1PH-DCAC: WAVEFORMS
Hello Sivarajan Please refer to the design guide for the waveform https://www.ti.com/tool/TIEVM-HV-1PH-DCAC#tech-docs Thank you Amir Hussain
View ArticleForum Post: RE: MSP430FR2433: MSP low-power microcontroller forum
Hey Luis, To clarify, you are not trying to connect the MSP-FET to the FR2433 and the P410R simultaneously, right? if it only happens when the Target is connected, then I assume the error is between...
View Article