Forum Post: RE: RM57L843: EMAC module’s MAC address
Thanks for the feedback and advice Jagadish! I'll pass this info along to my customer and will have them comment back on this thread directly with any follow-up questions they may have. -Matt
View ArticleForum Post: RE: TMS570LS1114: SafeTI Diagnostic Library fail to execute due...
Hi Albert, Have you solved the LDRA TAU issue with your HALCOGEN CSP? (+) TMS570LS1114: SAFETI-HALCOGEN-CSP execution problems - Arm-based microcontrollers forum - Arm-based microcontrollers - TI E2E...
View ArticleForum Post: RE: TMS320F28P650DK: How the MCAN recovers from a CAN bus off status
Hi Jinlong, Please refer to my FAQ: (+) [FAQ] TMS320F28P559SJ-Q1: The procedure to recover from CAN Bus-Off - C2000 microcontrollers forum - C2000 ︎ microcontrollers - TI E2E support forums
View ArticleForum Post: RE: MSP430F5503: SPI RX Problem
You seem to be using the STE signal to frame bytes. It doesn't do that on the MSP430. When STE is disabled, it simply pauses the SPI port. When it gets asserted again, the shift register picks up...
View ArticleForum Post: RE: TMS320F2812: XDS200 and CCS 12
Hi Joe, To understand the memory map, you can refer to the linker cmd file (F2812.cmd). For example, flash memory begins at the address 0x3D7800. Have you tried viewing those locations in the Memory...
View ArticleForum Post: MCU-PLUS-SDK-AM243X: Flash Protocol Changes causing problems with...
Part Number: MCU-PLUS-SDK-AM243X Tool/software: This is a new thread based on "MCU-PLUS-SDK-AM243X: Flash Protocol Changes" at the request of TI. The summary is that OSPI bootloader fails within...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: Flash Protocol Changes
The summary of the above thread is that OSPI bootloader fails within parseMultiCoreAppImage() for protocols other than 4S-4D-4D when using QSPI NOR. By examining the FSS memory, it was discovered that...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: Flash Protocol Changes
Hi Vaibhav, thank you for your support for the last several months. Joe
View ArticleForum Post: RE: AM2432: Problem with acyclic data in Profinet
Hi Kamil, thank you for your response. I am using the tool Profinet Master Simulator . Best regards, Andrea
View ArticleForum Post: RE: AM2634-Q1: AM2634 integration with eMMC reference design or...
Hi Divya, The MMC on AM263 supports MMC4.3 specification. I haven't studied the difference between MMC5.1 and MMC4.3. I think that the MMC5.1 is not fully supported.
View ArticleForum Post: RE: LAUNCHXL-F28379D: Assistance Required with Comparator Module...
Hi Tasmiya, I don't see any EPWM code provided in your snippet. It looks like you are just routing the output of the CMPSS to multiple GPIOs through the OUTPUTXBAR FYI the EPWM module is configured to...
View ArticleForum Post: RE: TMS320F28P650SH：TMS320F28P650SH
Hello, This expert is currently out of office until 10/21, so please expect a delay in response before then. Thank you for your patience. I also wanted to refer you to the CLB Tool User's Guide in the...
View ArticleForum Post: MSP430FR2433: UART TX interrupt
Part Number: MSP430FR2433 Tool/software: Tool: CCS 12.7.1 Hi all! C an someone give me a hand about this code? #include #define MCLK_FREQ_MHZ 1 // MCLK = 1MHz void Software_Trim(); // Software Trim to...
View ArticleForum Post: RE: TMS320F280039: CMAC check in customer bootloader
Hello, This expert is currently out of office until 10/21, so please expect a delay in response before then. Thank you for your patience. Best Regards, Allison
View ArticleForum Post: RE: TMS320F2800157: Debug problem
Hello, This expert is currently out of office until 10/21, so please expect a delay in response before then. Thank you for your patience. Best Regards, Allison
View ArticleForum Post: TMS320F28379D: Can CCS be configured to break execution when a...
Part Number: TMS320F28379D Tool/software: The thread title says it all. It would be a wonderful time saver if CCS can be configured to break execution when the value in a data or control register is...
View ArticleForum Post: RE: TMS320F28377D: JTAG Test connection shows not problems,...
Hi, I apologize for the delay getting back to you. Are you still having this issue? Could you please watch your clock with an oscilloscope? This sounds like it could be a clocking issue, as you...
View ArticleForum Post: RE: TMS320F28388D: SysConfig Possible Bug
Hello, This expert is currently out of office until 10/21, so please expect a delay in response before then. Thank you for your patience. Best Regards, Allison
View ArticleForum Post: RE: TMS320F28388D: Could not receive data about can...
Hi JeongMo, Is there a transceiver connected to pin 122 and 123 on the docking station? Regards, Joseph
View ArticleForum Post: RE: TMDSCNCD28388D: Configuring the CLB Output on an GPIO
Hello, This expert is currently out of office until 10/21, so please expect a delay in response before then. Thank you for your patience. I also wanted to refer you to the CLB Tool User's Guide in the...
View Article