Forum Post: RE: ADC of TMS320F28377D
Hi Keyur, Yes Yes....You can configure accordingly as per your requirement. Regards, Gautam
View ArticleForum Post: RE: ADC Start of Conversion Round Robin vs High Priority
Hi Frank, This has been explained very well with appropriate diagrams in ADC Userguide Section 1.4 ADC Conversion Priority. Regards, Gautam
View ArticleForum Post: tms570ls0432
sir, I had made the pcb by using launchpad schematic by removing xds100v2 circuit i.e. sheet no. 3 & 4 of TMS570LS04x launchpad schematic. for my CAN node and for programming i bought the xds100v2...
View ArticleForum Post: RE: TI msp430-gcc howto remove unused symbols without removing...
Rick Kimball could you please update the link in your posting as it does not point to any specific posting anymore. Thanks in advance.
View ArticleForum Post: RE: TI msp430-gcc howto remove unused symbols without removing...
It seems to have been deleted, maybe they fixed it.
View ArticleForum Post: Programming Piccolo Without Unlocking the Flash Manually
Hi, I know how to lock/unlock f28069 and program/erase the password using the UniFlash software. However, I was wondering if I can my program to automatically go through the lock and program the device...
View ArticleForum Post: RE: TI msp430-gcc howto remove unused symbols without removing...
[quote user="Rick Kimball"]It seems to have been deleted, maybe they fixed it.[/quote] I wanted to check your posting in the compiler forum first because I ran into a situation where the...
View ArticleForum Post: MSP430G2553 ,ADC10 and WDT Trigger
Hi, I am using MSP430G2553 in my design. I want Watchdog timer to trigger ADC10 Conversion in an interval of 1 msec. I am operating ADC10 in single sequence mode and total number of ADC channels are 4....
View ArticleForum Post: Updating firmware using legacy interface
We are using a Tiva processor to replace an existing system that has an established RS-232 protocol that supports downloading binaries and we would like to continue to use this method for system...
View ArticleForum Post: RE: MSP430G2553 ,ADC10 and WDT Trigger
1. Yes. You're right. Please avoid waiting in ISR. Can you wake MCU from LPM mode(in WDT ISR) and trigger ADC in main? 2.Use hardware multiplier( _IQMath ) Please read the documentation before you...
View ArticleForum Post: RE: Pushbutton interrupt code MSP430FR4133
Thank you very much for your support. The code works perfectly now. Thank you again for your help.
View ArticleForum Post: RE: MSP430G2553 ,ADC10 and WDT Trigger
Hi tejaChintalapati, Thank you for your quick reply I have modified the code as per your suggestion .!!! 1)Please go through and suggest me weather is this a right way to proceed? // Please note that...
View ArticleForum Post: RE: Updating firmware using legacy interface
The place to start would be to check the bootloader examples Robert
View ArticleForum Post: Motorware version 7
Hello Team, I am working on motor control project, which is based on instaspin FOC version V1.01.00.07. It would be of great help, if it is possible to share Motorware 7 version software, so I could...
View ArticleForum Post: RE: *** CRITICAL **** Do NOT use CCS v6.1.3
Shouldn't this bug be posted at the top of the Code Composer forum. Also, shouldn't there be a note (i.e. IMPORTANT:....) in the CCSv6 wiki (i.e....
View ArticleForum Post: RE: Updating firmware using legacy interface
After some thought, I can use the .CMD file to place a section of code in high flash and use that to make the copy occur at the right time.
View ArticleForum Post: RE: Is there any frequency constraint for msp430f5438A device...
Thanks for your help! I really appreciate it!
View ArticleForum Post: RE: Floating Point Unit Issue in TM4C123GH6PM
[quote]Any idea why ?[/quote] Either the FPU is not enabled at all, thus failing on the first FPU instruction. Or, saving the FPU context during interrupts is enabled, but the stack is not large...
View ArticleForum Post: Msp430f5438a: adc12 problem
I am trying to test a adc12 example code from texas. The code is correct, but when I try to connect a voltage signal at configured adc port the following message appears: msp430 trouble halting target...
View ArticleForum Post: RE: Sticky: MathWorks Solutions for C2000 MCU’s
Hi Brian, How to program the CPUs (I mean divide the tasks between CPUs) for F28377D using matlab embedded coder, also programming the CLAs? No examples shows the work with this processor.
View Article