Forum Post: RE: Using Boot Loader on MSP430FR6972 via RF
Hi David, I have tried to run small test sofware using the linker file generated by MSPBootLinkerGen but i got an error on the IAR message section as Fatal Error[e72]: Segment DATA must be defined in a...
View ArticleForum Post: F28377s boot mode change without JTAG
HI I have a F28377s DSP in a small evaluation board and I want to boot my board by USB boot.. or SPI.. NOT SCI... of course I can boot from internel Flash.. but want to boot from USB but i think there...
View ArticleForum Post: Hardware or Firmware/Software Problem?
Dear Sir: I own a couple of MSP430F USB Launchpads and I am trying to determine if I have software/firmware or a hardware problem with one of them. At the end of the day I am trying to determine if one...
View ArticleForum Post: MSP-EXP430FFR5969 launchpad
Hi, I have used ‘MSP430 graphics library reformer 2.00.00.17 ‘ to convert image (.jpg) in to code. The look up table generated does not look compatible with “preloaded images/Ti_logo.h”. I am using...
View ArticleForum Post: F28377s boot from USB and FLASH both
F28377s boot from USB and FLASH I want to boot my board via USB and FLASH boot mode of course I have a JTAG emulator (SDS100) but when I'm not the my office... want to use USB Boot for f/w upgrade......
View ArticleForum Post: RE: How to set communication between Matlab and Tiva via USB
Hi John, There are few questions I have for you: - Did you tried serial transmit/write using energia and send the serial data to comport. Are you able to read it? I used the same code that you wrote in...
View ArticleForum Post: TMS570 DCAN Module Extended and Standard
We have an application in which we use 6 message boxes, we use this configuration: 1: Send Extended identifiers 2: Send Standard identifiers 3: Receive standard message with identifier 665 4: Receive...
View ArticleForum Post: RE: MSP430FR6989 LC + ESI Power Consumption Issues
I attached the source codes that i am working with. The design note says that the whole system, except LCD, works with 7 uA for a sample rate of 500 Hz. Maybe my DMM is giving me false readings?. I...
View ArticleForum Post: RE: Cannot Program LAUNCHXL-F28377S after changing PLLSYSCLK
Hi, But right now my problem is I am not able to load any program on the board not even example programs. What should I do.
View ArticleForum Post: RE: +3.3V, VBUS and GND are indiacting short on DMM and the...
D- track of J11 micro-usb connector on tiva c tm4c123gh6pm launchpad has burnt out. How Where can I get that connection on the launchpad? Should I directly connect to PD4 of main MCU?
View ArticleForum Post: RE: Using the LM Flash Programmer for automatic flash updates...
I did not do any change change in bl_config.h or any of the bootloader code. But I changed SoftwareUpdateBegin: void SoftwareUpdateBegin(uint32_t ui32SysClock) { // // Disable all processor interrupts....
View ArticleForum Post: TMS320F28023/2 Flash Size
Hi, there are few conflicts in the datasheet and other places. What is the flash size of the: 1. TMS320F28023 2. TMS320F28022 Thanks in advanced.
View ArticleForum Post: RE: BLAC(aka PMSM) motor for DRV8301-69M-KIT evaluation board
Thank you Chris. Yes, I saw these motors but was not sure. I expected somewhere in description of the motor keyword PMSM/BLAC. It is a bit confusing to read 'servo' or 'encoder' on motor page title. Do...
View ArticleForum Post: Battery Backup System in MSP430FR-Series
Hi! I am searching for FRAM MSP with battery backup system or is this feature only available on F-series MSPs? I am searching for a solution to power the MSP (RTC) from battery if power is lost. Thanks...
View ArticleForum Post: RE: can_loopback example
Hello Hao, the hardware I used had a little bug. The GND pin of the CAN-transceiver wasn't connected. All I had to do was to connect the supply voltage of the CAN transceiver correctly. I guess the CAN...
View ArticleForum Post: RE: launchpad XL2 doesn't work
Thanks A lot for the great help, wish you good continuation have a nice day
View ArticleForum Post: HOW TO SAVE CALIBRATION DATA IN MSP430F425 FLASH MEMORY
I need help is saving my calibration data/factor on msp430f425 flash memory. Can anybody provide me source code for this. Thanks in advance.
View ArticleForum Post: RE: Missing Output Operating Condition on DRV8312
Nick, Please see attached pdf for the plots showing zoomed in before and after missing operation. (Please visit the site to view this file)
View ArticleForum Post: RE: The urgent prolem of PLC-G3
hi Qin, please use the " intermediate " gui of the Zero config GUI.to send raw packets to set / get the following PIBS. PIBs adpLBAMaxAttempts set to 2 with second last byte to 2 : as 0x0D 80 0E 00 D3...
View Article
