Forum Post: SPI synch issues
Hi, I am sending a counter value from one msp430 to another on a breadboard connected to two 7 segment LED's. The counter is an incremental counter. The hex value gets displayed on the 7 segment....
View ArticleForum Post: RE: Using MSP430 to interface microphone and speaker
[quote user="Datta Borkar"]Hi llmars, Thanks a lot for your advise! I will look into getting a hardware chip having DAC and DMA.[/quote]It's easy if you use parametric search. 1-series also have DAC.
View ArticleForum Post: RE: MSP430 Firmware update from external sdcard
[quote user="Troy Johnson"]Then update the micro's firmware using this new firmware file. Is such a thing possible? [/quote]Yes. You have to write your "SD card bootloader" - part of firmware which...
View ArticleForum Post: RE: CAN and DMA, TMS570 3137 HDK
This is perfect, dear Prathap!Thank you very much! I am moving forward with your help!
View ArticleForum Post: RE: MSP-GANG ERROR 68: FBSL initialization error
Thanks for your reply, SeaFesse,Given TI seem to be "owning" the MSP-GANG product, I thought it would be best to post the bug report to them, hence the post on this forum. (Is there another way to...
View ArticleForum Post: RE: how to find the dabort occur reason in TMS570LS3137?
Hi, Anthony：Glad to see your reply, the SP in the TMS570LS3137 will minus from the top(for example, the IRQ stack is from 0x08001200-0x08001500, the SP will start from 1500, then minus proper value...
View ArticleForum Post: RE: TM4C1233H6PM Bit Band failed on PD0,PD1,PB6,PB7
GPIO_O_DATA register is virtually mapped to 256 locations in the address space. To facilitate the reading and writing of data to these registers by independent drivers, the data read from and...
View ArticleClik here to view.
Forum Post: RE: LM3s8971 RDK & Ethernet ERBIAS missing resistor value?
The Boolean (t/f) and these patches made the PHY DHCP server assign the IP once a proper MAC address was established. Still wonder about that ERBIAS resistor value, quite concerning that is.
View ArticleForum Post: RE: Failed to run the TMS320F28035's FlashingLEDs cmd with...
Hi Eran,XDS is indeed a part of the kit, no doubt; I though you're using an external one. Anyways, can you check with CCS Uniflash and revert? Try dumping a .out file compatible with the...
View ArticleForum Post: RE: USART1 Transmits fine - does not receive
Yes - GIE is set and interrupts are working. Tom
View ArticleForum Post: RE: Interrupt on Cortex-M4
Hi Slandrum,I am using SysTick and getting some issue.Currently, my project built from an example one in TI REsource Explorer/TI-RTOS/ARM/Tiva C Series/Tiva TM4C123GHPGE/Example Projects. I just config...
View ArticleForum Post: RE: On my F28335 damaged.
Hi,I would like you to perform a small test:1. Configure your ADC modules sequentially and enable all of them.2. Give 3V signal to all of them 3. Observe ADC result registerThis itself will convey you...
View ArticleForum Post: RE: PCF 8575 interface with TMS320F28069
Hi Sagar,Will revert soon. Till then keep working.Regards,Gautam
View ArticleClik here to view.
Forum Post: RE: External Memory Initialize
Hi,Here's how you should configure "#pragma DATA_section"Regards,Gautam
View ArticleForum Post: RE: TM4c123GXL interrupt only fires once
Hi Roman, Does your Timer0IntHandler(), clears the Timer Interupt? You need to clear the Timer Interrupt. See below from the timer example program. I admire your coding with direct address...
View ArticleForum Post: RE: very very strange LM3S6911 problem, flash error?
Hi Yang, Isolate the root cause of the problem. Do a compare with a known working RDK-S2K board and your custom board. Run the same firmware, same set-up for long hours. If your custom board fails,...
View ArticleForum Post: RE: Debug Session hangs
Hi Ludger,I would like you to atleast check the behavior of CCS with other similar example codes. Also, you didn't mention what board you're using, kit or a custom board?Regards,Gautam
View ArticleForum Post: RE: I2C Slave Mode
Hi Markel, I did do a forum search and checked the examples before I wrote this post , none provide clarity on the master ack bit interrupt , instead there TREQ (Master Transmit Request) bit interrupt...
View ArticleForum Post: RE: USB 28069U disconnect USB stick while file access
Hi Roger, I was also trying to interface usb with 28069 devlopment kit. But i was unable to do that with the given sample code. When i have test the sample code at that time i am getting "unknown...
View ArticleForum Post: RE: How to use IF1 of DCAN3 to send data
These thread is not relevant with DMA translmitI want to transmit data with DMA.Is there some examples for DMA transmit?
View Article