Forum post: RE: MSP430F5659: Firmware Upgrade Corruption Issue
Hi Zrno Soli, Thanks for your reply.. Practically it is difficult for our application to limit the firmware size within 256 KB. Currently, it is 350KB around. I believe this solution(Splitting the...
View ArticleForum post: MSP430G2553: About serialization of MSP430 Gang Programmer
Part Number: MSP430G2553 Hello, MSP Gang Programmer (MSP-GANG) User's Guide 2.1.8 Serialization Is this operation NG without a PC? I tried to save the image in the internal memory of MSP-GANG...
View ArticleForum post: RE: CCS/TMS320F28377D: PWM sync operation
Hi vasudha, Thanks for reply. "Maximum 3 EPWMs" ?! Really? Are you sure about this? So why a master PWM (PWM1) and 5 slaves (2,3,4,5 and 6) are shown on page 1532 of TRM as is shown in attached photo?!...
View ArticleForum post: CCS/TM4C123GE6PM: I2C multiple read issue
Part Number: TM4C123GE6PM Tool/software: Code Composer Studio Hi i am have written I2C code to read TCS34725 devcie ID and able to send command and receive response but in my response i am getting only...
View ArticleForum post: RE: TMS320F28377D: ECC Logic Test for RAM using DxTEST register
Hi Vivek, I am creating single bit error in the D0 RAM at the address 0x00B000. This is a dedicated RAM memory and it is ECC protected as per the section 3.11.1.1 of TRM. Also, as I mentioned, I am...
View ArticleForum post: RE: CCS/MSP430FR6820: MSP430FR6820: FRAM variable definition
Hi lgi, I don't encounter any problem about your code : You can check if there are other errors in the cmd file. Best Regards Johnson
View ArticleForum post: RE: CCS/TMS570LS1224: SPI communication
Thank you so much for your reply.my issue is resolved.
View ArticleForum post: RE: CCS/TMS320F28377D: Unable to program new device
Hi Vamsi, Thank you for the response, I agree that closing this ticket is the right thing to do and separately trying to find out whether/why CCS 8.1 is still an issue. Thanks, Richard.
View ArticleForum post: RE: MSP430F5529: MSP430F5529, LMX2595
Hello, Please refer to MSP40F5529 code example and it's connections at below link. No pull-up capacitors needed. http://dev.ti.com/tirex/explore/node?node=AMFi4W25ksOBQrHkUQz8Nw__IOGqZri__LATEST
View ArticleForum post: LAUNCHXL-F28379D: SCI Bootloader
Part Number: LAUNCHXL-F28379D Hello everyone, I'm a beginner at TI programming. I'm doing a project like this: * Use bootloader to transfer code to RAM and execute it via SCI So I have couples on...
View ArticleForum post: RE: CCS/TMS320F28379D: ECAP prescaler for 2KHz signal measurement
Thank You Frank, But now it is difficult to use DSO probes in board. But i will try to get it. One question, what high and low level logic is required for eCAP ? is it TTL ?
View ArticleForum post: RE: CCS/TMS570LS3137: #10099-D program will not fit into...
My application is not a big. It's just test script. Your advice similar as my alternative decision. I expanded the FLASH_CODE area to 3 sectors. Everything fit, but again get error "failed to read...
View ArticleForum post: RE: CCS/MSP430FR6820: MSP430FR6820: FRAM variable definition
Hi Johnson, that is strange the same code works in your ccs. I changed few things and now it seems that works. I changed the last value in this part in cmd file: } PALIGN(0x0400),...
View ArticleForum post: TMS320F280049: import CCS
Part Number: TMS320F280049 When importing pfc1ph3ilttpl_F28004xCCS project, prompt:Product 'com.devkits' v2.5.1.00 is not currently installed and no compatible version is available. Please install this...
View ArticleForum post: RE: CCS/MSP430FR6820: MSP430FR6820: FRAM variable definition
Hi lgi, Yes, the compiler places them in order by default, so as you described, this variable will be placed at the first address of this segment. Best Regards Johnson
View ArticleForum post: RE: TMS320F28379D: Code Generation Error while Using CLA Task...
Hi, Please follow this link: and section: Select Inline Code Generation for CLA Subsystem
View ArticleForum post: RE: LAUNCHXL-F28379D: Communication error. LED D1 and D9 always ON.
Hi, Please try connecting from CCS and see if success. It is likely the board is not good. Try using different board. Contact MathWorks support if problem continues. Regards, Venkatesh C
View ArticleForum post: CCS/MSP430FR4133: MSP430FR4133
Part Number: MSP430FR4133 Tool/software: Code Composer Studio how can we use onboard button on MSP430FR4133
View ArticleForum post: CCS/DRV8312-69M-KIT: how to improve q-axis current tracking...
Part Number: DRV8312-69M-KIT Tool/software: Code Composer Studio Dear expert, I'm tuing current loop for SPMSM, no speed loop. the problem is id and iq are oscillating all the time. PI parameter for id...
View Article