Forum Post: RE: MSP430F5419A: ADC12 Interrupt Not Occurring
I find it interesting that your workaround includes explicitly turning off the ADCSC bit, since normally that turns off by itself. I have seen ADCSC stuck on, but only when it was set while ENC=0...
View ArticleForum Post: RE: MSP-GANG430: Serialisation & Log-file in standalone mode?
Hello Thibault, Unfortunately, I don't know of any way to do this and couldn't even come up with a proposal from the documentation. There is also not a built-in SD card reader to interface with. There...
View ArticleForum Post: RE: TMS320F28035: How to exit continuous mode of ADC in CLA task?
Hi,tlee T hanks for your help,Your answer is very helpful to me
View ArticleForum Post: RE: MSP430F1612: Thermal information request
Hey Jonathan, I can request this information from our internal systems team, but it will take a while to get feedback. Usually, they will provide it, but it may take a few weeks. Let me know if that's...
View ArticleForum Post: TMS320F28379D: Trip Zone ISR Not Being Entered But PWM Action Is...
Part Number: TMS320F28379D Hello, I am setting up a trip zone interrupt from a GPIO via Xbar and the PWM is able to respond to a trip event, but the ISR I wrote is not being entered. When I removed my...
View ArticleForum Post: RE: MSP430F1612: Thermal information request
Jonathan, I actually need to know which package this is for. Thanks, JD
View ArticleForum Post: RE: CCS/MSP430FR4133: UART worked in LPM0, but when i changed...
Thank you Mitch. i have known that i can't use SMCLK in LPM3. but i have seen something about Clock Request , Table 3-2. Clock Request System and Power Modes. I have understood i can use any clock...
View ArticleForum Post: RE: MSP430F5524: Using watchdog timer within a while(1) loop
The canonical way to use the WDT is to, within your "home loop" in main, reset the WDT each time around -- top or bottom, doesn't matter much. You can use the same code to start and to reset the WDT....
View ArticleForum Post: TMS320F28379D: power supply for the TMS320F28379D controlCARD
Part Number: TMS320F28379D Hi, I am using TMS320F28379D controlCARD. It has 2 options for the power supply, one from USB-5.0 using a zero resistor, R62, to connect with the following circuit and...
View ArticleForum Post: RE: MSP430G2231: Device does not run unless connected to debugger...
Hi Richard, Do you still get anything need to discuss? If not, should I close this thread and you could still post for another topic if have in the future.
View ArticleForum Post: RM46L852: GNU
Part Number: RM46L852 Dear team, How to compile RM46L852 with GNU？It shows “Selected device does not currently provide project initialization details for the GNU toolchain. The project may require...
View ArticleForum Post: RE: MSP432E401Y: CAN controller module sometimes unavailable at...
Hi John, That is interesting, I will have to look into this. I will get back to you if I find anything that may help. For now I recommend updating to the latest SDK. Thanks, Alexis
View ArticleForum Post: RE: MSP430FR2533: Fluctuation of power supply voltage
Hi I think just follow the recommend operation in the datasheet is ok. Refer to table 5 https://www.ti.com/lit/ds/symlink/msp430fr2533.pdf Best regards Gary
View ArticleForum Post: RE: CC430F6137: CC430f6137 clock setting issue
Hi, Congratulations, if you have any question later, please create a post to discuss directly in the E2E community. Best Regards Johnson
View ArticleForum Post: RE: EVM430-FR6047: EVM430-FR6047:
Hi Suhas, I haven’t heard from you for six days, so I’m assuming you were able to resolve your issue. If this isn’t the case, please click the "This did NOT resolve my issue" button and reply to this...
View ArticleForum Post: RE: CCS/LAUNCHXL-F28379D: emif_dc_flash,emif daughter card of...
Dear Tommy, Thanks a lot for your answer. Now I have another question.Since I have left the pin BYTE# unconnected,I found that the flash could enter the CFI Query mode by writing the CFI Query command...
View ArticleForum Post: CCS/TMS570LC4357: question about ESM Group3 error filtering at...
Part Number: TMS570LC4357 Tool/software: Code Composer Studio Hello I have a problem which is still not resolved myself. previously i posted same question. the random error occur at ESM group3 error....
View ArticleForum Post: RE: CCS/EVM430-FR6047: water flow measurement
Hi, Can you reduce the sampling frequency to 4000 kHz and increase the UPS0 to UPS1 gap to 150ms? When you click on "Request Update" can you confirm that the update was successful? BR, Leo
View ArticleForum Post: RE: TMS320F28377D: configure 28377D 16bit differential ADC to...
Hi Joseph, Thank you for your answer! I have removed D1 and D2 from the eddy current sensor signal conditioner, and the becomes the following picture.（But I am not sure the PD pin of THS4531 is 3.3V or...
View ArticleForum Post: MSP430F5509: MSP430F5509
Part Number: MSP430F5509 Hello, Could you help check below question of MSP430F5509IRGCT and answer it? 1. Is this IC a membrane process? 2.What is the base material of this IC? 3.Does it contain...
View Article
