Forum Post: MSP432P401R: Confusion on SPI Port Mapping for P2.x
Part Number: MSP432P401R Hello, Pardon me for the repost question about the port mapping for SPI peripheral on MSP432P401R. My concern is I can't find the consistency between TI PinMux Tool,...
View ArticleForum Post: CCS/LAUNCHXL-F28377S: Load symbls
Part Number: LAUNCHXL-F28377S Tool/software: Code Composer Studio TI technical support, I import cla_adc_fir32_cpu1 from C2000Ware to CCS. It prompts no symbls are defined. Where are symbols gotten...
View ArticleForum Post: CCS/ARM-CGT: ARM Cortex M4F
Part Number: ARM-CGT Tool/software: Code Composer Studio Hi, how to initial the ARM Cortex M4F chipset device bus?
View ArticleForum Post: CCS/LAUNCHXL-F28377S: EPWM1 in cla_adc_fir32_cpu01
Part Number: LAUNCHXL-F28377S Tool/software: Code Composer Studio TI technical support, In cla_adc_fir32_cpu01 it is said that "It will setup EPWM1 to triger ADCA at a frequency of 50KHz." It seems...
View ArticleForum Post: TMS320F28377S: can not install usb driver
Part Number: TMS320F28377S Hi Team, My customer are using USB function of TMS320F28377S and verify this function ok in his computer, when they connected usb port on TMS320F28377S to some of other...
View ArticleForum Post: TMDSHVMTRPFCKIT: Problem about Current sampling
Part Number: TMDSHVMTRPFCKIT Recently I was doing experiments with TMDSHVMTRPFCKIT, After looking at the hardware schematic diagram, I found that the rated current of the board is - 10A ~ 10A. The...
View ArticleForum Post: TMDSHVMTRINSPIN: howto apply to my custom design?
Part Number: TMDSHVMTRINSPIN Dear TI Experts: For the TMDSHVMTRINSPIN with a TMDSCNCD28069MISO control card, we can find many InstaSpin projects provided by TI. For a PMSM FOC control with 3 Rshunts,...
View ArticleForum Post: CCS/MSP432P401R: use of GPIO pins for I2C and UART
Part Number: MSP432P401R Tool/software: Code Composer Studio Hi, I'm planning to use MSP432P401R 64pin VQFN Package. As I can see it supports only 3UART(eUSC) If I want to use 6UART and 5 SPI can I use...
View ArticleForum Post: TMS320F28030: TMS320F28030PAGQ for Automotive Application
Part Number: TMS320F28030 Dear C2000 Team One of my customer is planning to use TMS320F28030PAGQ for an motor drive application where safety is required ASIL-B. Could you please let me know if we have...
View ArticleForum Post: EK-TM4C1294XL: I2C Interrupt
Part Number: EK-TM4C1294XL Hi I'm not able to get interrupt form I2C. Is the following setup code right? // set PB2, PB3 for I2C GPIOPinTypeI2C(GPIO_PORTB_BASE, GPIO_PIN_2 | GPIO_PIN_3); // I2C over...
View ArticleForum Post: CCS/CC430F6137: RTC CALENDAR MODE CODE DEVELOPMENT
Part Number: CC430F6137 Tool/software: Code Composer Studio Dear Sir/Madam, I'm working in Real Time monitoring system project. Already find and download example for your TI RESOURCE EXPLORER example...
View ArticleForum Post: TM4C1294KCPDT: TM4C1294KCPDT for new development
Part Number: TM4C1294KCPDT We are going to use TM4C1294KCPDT controller for our new design of product. In earlier product, we use Luminary LM3s6965 contoller which becomes obsolute after over...
View ArticleForum Post: RE: TM4C1233H6PZ: ADC - uDMA issue
The uDMA burst request is gated by the interrupt enable bit.
View ArticleForum Post: CCS/LAUNCHXL-F28069M: Flash programming
Part Number: LAUNCHXL-F28069M Tool/software: Code Composer Studio Hello, I want to program the Flash of TMS320F28069M for stand alone application. So far,I did this steps: 1) adding : a) F28069.cmd...
View ArticleForum Post: RE: CCS/TMDSHVMTRPFCKIT: TMDSHVMTRPFCKIT
You may check if the switches on HV-kit and F28035 controlCard are correct as of the guide in below folder. C:\ti\controlSUITE\development_kits\HVMotorCtrl+PfcKit_v2.1\~Docs And you may have a look at...
View ArticleForum Post: RE: TMS320F28335: What affects Flash's erase time of F28335 ?
Hi, Please review the FAQ answer on this below. It should answer your questions on this. https://e2e.ti.com/support/microcontrollers/c2000/f/171/t/758747 Best, Kevin
View ArticleForum Post: LAUNCHXL-F280049C: LAUNCHXL-F280049C
Part Number: LAUNCHXL-F280049C I have a related issue. I upload my project to the F280049C and run the program from CCS, it behaves a certain way. My power to the board supplied by the USB I uploaded...
View ArticleForum Post: RE: CCS/TM4C1294NCPDT: Error while dumping the code in customized...
It looks like the JTAG signals are good. Check the voltage on the RST pin. You should add a pullup resistor.
View ArticleForum Post: RE: TMS570LC4357: Read a specified Flash memory in Tms570lc4357
Hi Hamideh, Please confirm the contents of all ESM status registers. Please also confirm that you do program the correct ECC for the entire 4MB of Flash memory. Regards, Sunil
View ArticleForum Post: RE: LAUNCHXL-F280049C: Error while uploading ending in process...
Darryl, [quote user="Darryl Ols"]However I found all these examples in the folder for this board. see capture 8. So that's why I thought there was no problem on my end. Please correct me if I'm...
View Article