Forum Post: MSP430F6736: Low Power Mode set and exit in MSP430F6736
Part Number: MSP430F6736 Hi all, I'm working with MSP430F6736 controller. I want to interface other devices using UART. During serial port initialization, I set the low power mode...
View ArticleForum Post: RE: CCS/MSP432P401R: Sampling for a pulse
If you're interrupting on every conversion in fast-as-possible mode, you will (my prediction, but do the arithmetic) spend all your time in the ISR, since the samples are arriving faster than you can...
View ArticleForum Post: RE: RTOS/TM4C1294NCPDT: Mailbox behavior in TI-RTOS...
Hi Rob, I understood task synchronization while executing mailbox critical section. If mailbox (e.g. M1) is executing critical section because of POST(M1) from task T1 or PEND(M1) in task T2 and now...
View ArticleForum Post: RE: TMS320F28377D: Interfacing ADC ADS8568 with MCU TMS320F28377D
Hi Devin, Thanks for your quick response. The start of conversion of external ADCs need to be synched with ZERO match of ePWM. Moreover,we have to select the external ADCs with right timing.The...
View ArticleForum Post: RE: TMS320F28335: epwm
I read about the E-PWM interrupt , but i have not tried it yet. I'll try and let you know.
View ArticleForum Post: CCS/TIDM-HV-1PH-DCAC: TIDM-HV-1PH-DCAC
Part Number: TIDM-HV-1PH-DCAC Tool/software: Code Composer Studio Hello, I intend to use this TIDM-HV-1PH-DCAC kit to experiment various control schemes. Is it possible to use other controllers...
View ArticleForum Post: CCS/MSP432E401Y: CCS9.0/Build Error
Part Number: MSP432E401Y Tool/software: Code Composer Studio Hi. I'm trying to build an example in simplelink_sdk_wifi_plugin_2_40_00_22. I'm using CC3120 booster pack with MSP432E401Y launch pad. When...
View ArticleForum Post: MSP432E401Y: Finding vendor to provide programming socket for MSP432
Part Number: MSP432E401Y Hi expert, Could you let me know if there is any vendor who can provide programming socket for MSP432? Thanks Sheldon
View ArticleForum Post: RM48L952: no device packages of RM48L952 for Eclipse CDT
Part Number: RM48L952 Dear Sir I used RM48L952 used HalCoGen+FreeRTOS+GCC+RM48L950 to gen the source code then used Eclipse CDT( Eclipse IDE for C/C++ Developers Version: 2019-03 (4.11.0) ) now , it is...
View ArticleForum Post: CCS/TMS320F28377D: How to check/where to check CCS On-Chip Flash...
Part Number: TMS320F28377D Tool/software: Code Composer Studio We are using CCS 6.0.1 for TMS320F28377D development, how to check whether CCS On-Chip Flash Plugin is installed?
View ArticleForum Post: CCS/TMS320F28379D: CLK output
Part Number: TMS320F28379D Tool/software: Code Composer Studio Hi, The TIDA-01455 document explains as "The design features an interface to the C2000â„¢ Delfinoâ„¢ to generate up to a 20-MHz clock signal...
View ArticleForum Post: TMS320F28022: what's the advantage of Q100 version?
Part Number: TMS320F28022 Hi, in http://www.ti.com/lit/an/spra963b/spra963b.pdf the FIT Rate vs. Operating Junction Temperature doesn't show difference between Q100 version and Non-Q100 version for the...
View ArticleForum Post: RE: CCS/F28M35H52C: Code download to C28x results in Error...
Hi Kevin, After complete erase and re-flash, it is OK.
View ArticleForum Post: RE: RM48L952: Hercules secure boot functionality
Hello, Hercules MCUs does not support secure boot. You can consider AJSM ( Section 6.21.6 Advanced JTAG Security Module in Datasheet) for protecting your code. Best regards, Miro
View ArticleForum Post: RE: RM48L952: XDS200 PIN definition
Hello, Here is what I found: Table 2:XDS200 CTI20 Header and Adapter Pin Outs is where pins are defined Best regards, Miro
View ArticleForum Post: RE: TMS570LS0914: Start up code self test fails and SP pointing...
Marco, Thanks for assisting!!! Best regards, Miro
View ArticleForum Post: RE: TMS320F28374S: TMS320F28374S ADC inputs frozen after Flash...
Hi Devin, your suggestion has been fundamental: running the ADC sampling code from RAM loaded via JTAG allowed us to find the problem. In the Firmware, the ADC results were multiplied with a set of...
View ArticleForum Post: RE: CCS/TM4C1294NCPDT: Building multiple projects in a workspace
Hi Arti, I tried case 1, it worked for me successfully. But for case 2, I need help. In case 2: "Project_Main" has symbol "MACRO_1" in "Predefined Symbols" in "Project Properties". Is it possible to...
View ArticleForum Post: RE: OMAP
Hello, OMAPX5777 is basically pre-production, test device, evaluation EVM board that encapsulates all J6/VAYU superset functionality. So you got DRA756 in there. thanks, Alex
View ArticleForum Post: RE: MSP430FG4618:
Hi JD, I have done changes as suggested by i;m getting below error , this error is same as mention in the thread as well, as compiler won't allow AND operation on function pointer. #pragma...
View Article