Forum Post: RE: LAUNCHXL-F28069M: Error occurred while executing External...
Hi, 'Switches are set to on-on-on' is correct. You may want to load the virtual com port for the USB emulation of UART port by following the post:...
View ArticleForum Post: RE: TMS320F28335: ADC Conversion Failure
I'm sorry, but I paste the data as image file because the data is hard to see.
View ArticleForum Post: RE: CCS/TMS320F28379D: PMSM
FYI: I have a servo motor that I can set it in torque constant mode. I want connect it to a PMSM machine and control this machine speed at a desired speed. what requirements should I consider ?
View ArticleForum Post: RE: MSP-EXP430FR2311: High current draw, longer then expected...
Hi George, I will try to repeat your issue with your code. Get back to you later.
View ArticleForum Post: RE: CCS: Issue to Get IP address on while Compiling Ethernet...
Hi QJ Wang, I have verified RM57 is little endian device and both __little_endian__ & __LITTLE_ENDIAN__ is define in HL_sys_common.h file. I am still having the same isuue just because of this I am...
View ArticleForum Post: CCS/MSP430FR2633: Enable/ dissable the proximity sensor.
Part Number: MSP430FR2633 Tool/software: Code Composer Studio Hello, I am using captivate -phone board. Sensors used are numeric keypad and proximity sensor. I would like to know how to enable and...
View ArticleForum Post: RE: MSP430F5529: ADC12 A4 doesn't work
Hi Jacob, I find nothing wrong with MSP430F5529 Launchpad with your Channel 4 code. You need to check your hardware whether there is some short or something else impacts the MCU.
View ArticleForum Post: RE: TMS320F28379D: Does AQ shadow register still get loaded at...
Hi Cody, Yes, I agree that this a limitation that only makes the application tricky under certain scenarios. Thanks for your support. Regards, Brian
View ArticleForum Post: TMS320F280049: tidm_1000 "ADC_PU_SCALE_FACTOR" , how does this...
Part Number: TMS320F280049 hi All, I am studying the firmware of TIDM-1000 Vienna Rectifier-Based, Three-Phase Power Factor Correction (PFC) Reference Design. I found the ADC scale is define to...
View ArticleForum Post: TM4C123GH6PM: Program flash erasing
Part Number: TM4C123GH6PM We have been using TIVA microcontroller TM4C123GH6PM for many years over several projects . Since 2 years ago I started facing a problem in some of the boards due to Flash...
View ArticleForum Post: RE: CCS/TMS320F28379D: PMSM
No separate config is needed for generator, same config fits both. In generator mode, the current loop output generates a voltage reference that is a little lower than that of the motor back emf to...
View ArticleForum Post: RE: CCS/MSP430F5510: ReplicatorXv2 JTAG ID ISSUE
[quote user="farooq ahmad"] I am using msp430f5510 as a host and msp430f5308 as a target .Yes i have sucessfully programed it .There were some errors because project was made for msp430f5437 .I am...
View ArticleForum Post: RTOS/TM4C1294NCPDT: TM4C1294NCPDT
Part Number: TM4C1294NCPDT Tool/software: TI-RTOS Hi, Is there any watchdog timer example available for multi threaded environment. Is there any simple method available to know the task status. Regards...
View ArticleForum Post: RE: CCS/MSP430F5659: Parallel Communication in MSP430F
[quote user="MOHIT KUMAR"] Part Number: MSP430F5659 Tool/software: Code Composer Studio Hi Everyone, I know that serial communication is very much often. But what about parallel communication. I want...
View ArticleForum Post: RE: CCS/TMS320F280049C: F280049C, can't program DCSM
Hi Vivek, I got a new problem If I didn't write DCSM and set DSECT to DCSM. The following are my settings. I could execute my program successfully with this setting. However, the program could not be...
View ArticleForum Post: RE: MSP430F47187: HOW we use DLMS stack for Tampers,selective...
Hi Peeyush, I have sent you a one-to-one email answering your queries. Pls let me know if you have any further queries directly by email. Regards, Chander
View ArticleForum Post: RE: EVM430-FR6043: VOL IN LITERS always shows 0
Hello, How about your issue?
View ArticleForum Post: RE: CCS/MSP430F5510: ReplicatorXv2 JTAG ID ISSUE
Thanks for your guidance.i will check all ports signals again .I am not familiar with high level functions used in this code.
View ArticleForum Post: RE: TMS320F28069F: controlSUITE : a problem in using the...
Dear Sal, Thank you for your review. Today I have worked with the serial_flash_programmer.exe utility program nearly all day. As a result, I have found out the reason that the serial_flash_programmer...
View ArticleForum Post: RE: MSP430FR2433: HID Support
We have not try that. So we don't have the information and sample code you need. You can send me email to share the customer project background. We can discuss if it needed to evaluate this demand and...
View Article