Forum Post: RE: CCS/LAUNCHXL-F28379D: PMSM Motor Direction - Forward/Reverse
What example lab/project are you referring? For sensored/sensorless-FOC mode, you don't need to do anything on hardware, only need to set a negative reference speed or negative torque current that will...
View ArticleForum Post: CCS/TMS320F28030: Resource Explorer not opening
Part Number: TMS320F28030 Tool/software: Code Composer Studio Hi Resource explorer does not progress beyond the opening page TRIX, the TRIX symbol continues to rotate. Can you suggest a solution the...
View ArticleForum Post: Compiler/TMS320F28030: Value of variable and location in memory
Part Number: TMS320F28030 Tool/software: TI C/C++ Compiler Hi the variable is not displayed when the cursor is hovered of the variable, can this be enabled? thanks
View ArticleForum Post: Compiler/TMS320F28030: Value of variable in the debug mode
Part Number: TMS320F28030 Tool/software: TI C/C++ Compiler Hi variable are not displayed when the cursor is hovered over the variable, can this be enabled? Version: 7.2.0.00013 thanks
View ArticleForum Post: Compiler/MSP430G2553: SERVO MOTOR CONTROLS
Part Number: MSP430G2553 Tool/software: TI C/C++ Compiler I wrote this program but it has some errors as follows 1.Unstable output pulse response 2.No synchronous control of all 3 motor I have read...
View ArticleForum Post: MSP430F5418A: Can I suggest which version IAR for customer...
Part Number: MSP430F5418A Dears: I provide the below software's link to let customer evaluating the performance of MSP430F5418A . However, the customer uses the newest version IAR(EW430-7121-Autorun),...
View ArticleForum Post: CCS/TMS320F28377S: How can I setup TMS320F28377S Boot pin...
Part Number: TMS320F28377S Tool/software: Code Composer Studio Hello Guys: I am working on TMS320F28377S platform for a instruments project, I have selected QFP176 package for this application, In my...
View ArticleForum Post: RE: CCS/TMS320F28069M: How to induce CAN communication errors
Thank you sir! Will you please tell me how to get into bus active mode after bus off. Another is I want to forcefully do node off, what should I do?
View ArticleForum Post: TM4C1294NCPDT: SSI timing specification for SPH=0
Part Number: TM4C1294NCPDT Hi, I have qestions about SSI timing for TM4C1294NCPDT . I would like to use SSI with SPH = 0. However, the timing chart for SPH = 0 is not described in the data sheet, and...
View ArticleForum Post: RE: MSP430F5529: Confusion about the USCI35 entry in MSP430F5529...
Hi, Mostly SDA will change the voltage on the falling edge. And the data is only valid on the low voltage of SCL. Just see the errata, it means it is possible that restart has problem in standard mode...
View ArticleForum Post: RE: TMS320F28379D: How many CLAs ARE present in TMS320F28379D?
Hi Ashwin, Please refer to the device specific datasheet. Regards Himanshu
View ArticleForum Post: RE: MSP430F6777: About the signal width input to the reset pin.
Hi da, If this pulse width is shorter than specified, the device may go into an uncertain state (may can't work). The pulse duration is for ensuring all logic have been reset. Regards, Stanford
View ArticleForum Post: RE: MSP430F5529: ADS1293 spi interface MSP430F5529 problem
Hello Eason, I downloaded the library again and proceeded according to the guide. Thankfully, it worked. Probably there was some mistake with loading the library from me for the first time. Best...
View ArticleForum Post: RE: MSP430F47187: HOW we use DLMS stack for Tampers,selective...
Hi TI team, kindly help for above issues facing in DLMS .
View ArticleForum Post: MSP430XXX as USB HOST ?
Dear Can I want to find one MSP430 chip that it can be as USB host and access an 32GB USB flash drive with file type. THANKS
View ArticleForum Post: RE: MSP430G2553: USCIAB0TX_VECTOR working
Hi AMITKUMAR, Right. When the TXBUF is empty, it will set UCAOTXIFG, and if you enable the TX interrupt, you will jump into USCIAB0TX_VECTOR, then you can send a new data to the TXBUF. Best regards,...
View ArticleForum Post: TMS320F28377S: GPIO72 BOOTLOADER FUNCTION Shield?
Part Number: TMS320F28377S Hi Sir, We are using TMS320F28377SPTPT now in our product. and use an Ethercat MICROCHIP LAN9252; When LAN9252 initialize, DAT12 Pin(connect to F28377S GPIO72 pin) will drop...
View ArticleForum Post: TMS320F28377D: Delfino EtherCat failure analysis
Part Number: TMS320F28377D Hi Sir There is an EVM on my hand, you can see in "TI Designs EtherCAT® Interface for High Performance C2000™ MCU; file # is TIDUBQ6A; link:...
View ArticleForum Post: TMS320F28377S: DCSM changing LINKPOINTER value
Part Number: TMS320F28377S Hi, Do I understand correct that if the linkpointers value is changed (SPRUHX5E P147) the zone lock is removed and the device is accessible again? - Is this also true if the...
View Article