Forum Post: RE: EVM430-FE427A: Can't get the user's guide and hardware design...
Hi Ted, Slaa302 can be found as below link but it's not for this EVM. I am trying to contact with the author, will back to you soon. www.ti.com.cn/.../litabsmultiplefilelist.tsp regards KC
View ArticleForum Post: RE: CCS/MSP430FR2000: Can not debug MSP430FR2000 with MSP-FET430UIF
Hi LOC, Would you please try to use CCS or IAR download the code so that the firmware in your FET can be updated. Regards, Ling
View ArticleForum Post: RE: CCS/MSP430FR2000: Can not debug MSP430FR2000 with MSP-FET430UIF
Hi Ling, Can you show me how to update firmware FET430 by CCS or IAR? Do you have any document ? Thanks,
View ArticleForum Post: RE: TMS570LS3137: TMS570LS3137 MIBSPI Slave configuration
Hello, Reset pull state of MIBSPI1 of TMS570LS3137 is as follows: MIBSPI1CLK - pull-up; MIBSPI1NCS[0] - pull-up; MIBSPI1NCS[1] - pull-up; MIBSPI1NCS[2] - pull-up; MIBSPI1NCS[4] - Pul-down;...
View ArticleForum Post: RE: MSP430FR6989: I2C: UCBCNTx register non-zero after a start...
Hi Igor Are you sure you just sent the address without any data? Can you capture the signal of the SCL and SDA when you execute the start command? Best regards Gary
View ArticleForum Post: RE: MSP430FR5994: MSP430FR5994 ADC in chip test
Hi Chen What's your test condition?(Reference, source and so on) We do have the linearity parameters and dynamic performance with internal or external reference in the datasheet . Best regards Gary
View ArticleForum Post: RE: MSP430FR5947: MSP430FR5947 memory mapping
Hello Sai, as stated by Clemens, from the memory and control register allocation point of view this is possible with compatible super set devices, like in this case. Please keep in mind, dependent on...
View ArticleForum Post: RE: CC430F5137: Using RF Studio Register settings in firmware...
CC1310 will be able to communicate with CC430 given the same datarate, deviation, modulation and packet format. You write: " I mean that the firmware seems to send the packet ". Does that mean that...
View ArticleForum Post: RE: MSP430FR6047: How to utilise the MTIF for generating pulses...
Hi Ramtin, I could not open that link. But I think you can check the MTIF function in the User's Guide. Best regards, Cash Hao
View ArticleForum Post: RE: CCS/MSP430FR2000: Can not debug MSP430FR2000 with MSP-FET430UIF
Hi Ling, I try to update new firmware for FET430UIF, but it report FET firmware is up to date (Firmware version: 3.11.00.001). Thanks, LOC
View ArticleForum Post: RE: MSP430F5359: Are the instruction opcodes 10C0 through 10FF...
Hi Atlant, these opcodes are really reserved. Executing a SWPBX is not really meaningful in the original sense of a swap byte, as the "X" expansion is related to the 20bit format, while the memory...
View ArticleForum Post: RE: CCS/MSP430F2274: Erroneous ADC values under elevated...
Hi Todd, Sorry that we need more information to understand the issue. 1. What's the failure rate you have found? 2. What kind of signal input to adc? Just to confirm, if the signal related with...
View ArticleForum Post: MSP430F5438: MSP430F5438
Part Number: MSP430F5438 Hello, We are using MSP430F5438 as host controller to configure Purepath IC CC8531 (slave). The connection between MSP430 and CC8531 are 4 slave lines (MOSI, MISO, CSN, SCLK),...
View ArticleForum Post: TM4C1294NCPDT: JTAG not detecting
Part Number: TM4C1294NCPDT Hi, We are using TIVA TM4C129NCPDT in our design. The problem is, TIVA is not detecting XDS200. Kindly let me know the work around. Regards, Sumathi
View ArticleForum Post: TMS320F28027F: DRV8305
Part Number: TMS320F28027F Hello, I have some general questions about TMS320F28027F and the reference design for a drone ESC ( TIDA-00643 ). I plan to produce high quality controllers and look for an...
View ArticleForum Post: RE: MSP430FR4133: AM power consumption depends on code location...
Hello Andre, please keep in mind there are multiple components, which influence the active current of the MCU/CPU. The basic point is the nature of the CPU current. It is the current of a clocked...
View ArticleForum Post: RE: MSP430FR6972: MSP430 UART connection with PC
How exactly are you interfacing the MSP with the serial bus? The voltage levels of the MSP's 3.3 V CMOS logic and RS-232's ± 15 V are quite different, and a logic "one" is represented in RS-232 with a...
View ArticleForum Post: RE: CCS/MSP430FR5949: SPI communication problem between MSP430FR...
Hello Henrique, did you check the HW in the sense of monitoring the SPI communication with a scope? Are the signals reflecting what you're transmitting and receiving? Best regards Peter
View ArticleForum Post: RE: MSP430FR6972: Does Controller enter LPM if one of the GPIOs...
Where does the datasheet say that GPIOs must not sink/source current? Footnote (1) of table 5.9 just says that the values were measured without any current through the GPIOs; if they GPIOs do...
View ArticleForum Post: RE: MSP430F5438: MSP430F5438
Hello Jeyaprakash, according to your description the RST pin of the MSP430 is somehow connected to the CC8531 device, is this correct? What is happening to the RST signal in case you're not powering...
View Article