Forum Post: RE: MSP430FR4133: update my setting
To get this changed, I would recommend contacting the support center as the forum is used for engineering support. I do not have access to any internal tool to change this for you, but the support...
View ArticleForum Post: RE: F28M36P63C2: USB TX and RX interrupts stop firing
That issue should only pertain to the USB library running on the C28x. But it would not hurt to try it at this point. Please see the latest code in C2000Ware . I believe there were two functions...
View ArticleForum Post: RE: TMS570LS3137-EP: TMS570LS3137 FLASH
Rajeeva, The 5year published limit is based on testing at 250c using Arrhenius model. There is no practical way to wait 5 years for testing, so accelerated testing is used. That is the intent of note...
View ArticleForum Post: RE: CCS/TMS320F28379S: Boot mode for 28379S
Hello I haven’t heard from you for a couple weeks, so I’m assuming you were able to resolve your issue. If this isn’t the case, please reject this resolution and reply to this thread with your latest...
View ArticleForum Post: RE: TMS570LC4357: Trig : L2RAM: "Uncorrectable error Type A:...
Yes, you are right. For LC43x, there is only one L2RAM control registers whose base address is at 0xFFFF_F900.
View ArticleForum Post: RE: TMS320F28075: Abnormal behavior of IN_MODE configuration of ePWM
Hi, If you are using IN_MODE=2 then the complementary operation of PWMA and PWMB is not guaranteed by default in the hardware, because there is dependency of software updating the CMPA and CMPB...
View ArticleForum Post: RE: CCS/LAUNCHXL-F280049C: CCS/LAUNCHXL-F280049C...
Do you by chance have the connection open in another window? Sometimes if you do a "test connection" while the debugger is connected in the Debug view, it will fail since one of them already has the...
View ArticleForum Post: RE: CCS/TIDM-BIDIR-400-12: ADC,
Hi Kyoungtak, I am sorry for the delay. Yes, the Gui_Ifb value is not very accurate mainly because of the low power operation. Your result does look much better. As for the ADC result being double the...
View ArticleForum Post: CCS/DRV8301-69M-KIT: SpeedRef_Krpm keeps on increasing...
Part Number: DRV8301-69M-KIT Tool/software: Code Composer Studio I am working on lab12b , everything was working well before. Now I observe that whenever I set SpeedRef_krpm to certain value ,...
View ArticleForum Post: RE: CCS/TMS320F28069M: F28069M getting stopped after running for...
Zesto, Hope your new year's celebration wasn't spoiled by your board issues! I have some questions/comments: - Have you verified that your MCU is soldered properly? I assume that you checked for any...
View ArticleForum Post: RE: CCS/MSP432P4111: MSP432P4111 + EnergyTrace error
Hello, Can you test a low power example to see if the device is functioning correctly? If it consumes too much current, more than 5uA with debugger disconnected, then look for a damaged pin. You can...
View ArticleForum Post: RE: CCS/TMS320F28069: USB 28069U IC
Hi, You can use a ROM bootloader to load a program into RAM and run that program. You can also use the serial flash programmer or USB flash programmer to load an application into flash. Please see...
View ArticleForum Post: TMS320F280049: Data mismatch happen with some burst...
Part Number: TMS320F280049 https://e2e.ti.com/support/microcontrollers/c2000/f/171/t/749786 Based on the above test, I found an strange problem.There is mismatch(error) for some received data with some...
View ArticleForum Post: RE: CCS/EVM430-FR6047: Print result in next line using UART
Hey Divya, Are you wanting to see the data pointer in the CCS terminal? Are you trying to see the data while debugging or sending the data to the PC via the UART? You can also use the printf statement...
View ArticleForum Post: RE: MSP430FR2633: Unable to get proper value at Start and End...
Hello Gourav, Sorry for the late reply due to the holiday. I checked your code with your layout but still did not see anything that could cause your issue.The only way for me to reproduce what you seen...
View ArticleForum Post: RE: MSP430F2252: PMP8740 : Schematic and coding related.
Hello Vijay, I've notified Robert of this thread, but there may be some delay in response due to the new year. Looking at your questions, they seem to be about the PMP8740 hardware design questions....
View ArticleForum Post: RE: TMS570LC4357: Trig : L2RAM: "Uncorrectable error Type A:...
Hello, The bit 22 and bit 20 of status register are set after the test is triggered. The channel 7 of ESM group 2 is set, and channel 3 of ESM group 3 is set too. The Channel 7 of ESM group 2: L2RAMW -...
View ArticleForum Post: CCS/TMS570LS3137: Is there a way to open two debug sessions...
Part Number: TMS570LS3137 Tool/software: Code Composer Studio We are running our code and third party code simultaneously, The Third-party code (a Javascript with a target connection) has control of...
View ArticleForum Post: RE: CCS/MSP430FR2355: Problem with LPM3 current (it is extremely...
Hi Bruce, This worked - I'll have to go read more on the clocks; thanks for all your help! I have two follow up questions, however - first is that the current in the active mode is just a couple of uA....
View ArticleForum Post: RE: TIDM-1002: Cannot run PC-GUI for ultrasonic eval board. Log...
Here is the log file error messages... 01.02 17:22:22 Current dir: C:\ti\msp\gasLibrary_1_10_00_11\GUI 01.02 17:22:22 Loading 64 bit Windows rxtx Jan 02, 2019 5:22:22 PM com.ti.msp.gui.uss.ComRead...
View Article
