Forum Post: RE: TMDSSOLARUINVKIT: Vbus is approximately 0
Board input should come from PV panel. So I am not sure what exactly you meant by "2 poles of the PV on the board input". Please read the Quick Start Guide (QSG) carefully and follow the procedure to...
View ArticleForum Post: RE: CCS/TMS320F28069: MOTORWARE
Rasool, Looking at motorware lab 3, I'm not certain that the CLA is used in this example(I don't see any .cla files or reference in the lab docs). In this case there's no need to have a concern about...
View ArticleForum Post: RE: CCS/LAUNCHXL-F28379D: Transmitting SPI Data from one...
Tyler, I have never used Simulink SPI receive function. So, I really cant comment on that. But, did you check with an oscilloscope whether SPI is indeed transmitting? Regards, Manoj
View ArticleForum Post: RE: CCS/C2000WARE: Piccolo Microcontroller - Flash ECC test
Bhageerath, If you have it enabled, can you disable and try? Let me know if that works. Thanks and regards, Vamsi
View ArticleForum Post: RE: MSP432E401Y: USB Not Connecting to Computer
There should be no other step required to get the usb example running except to connect up both the USB cables to the computer. Your hardware connections checkout. Just so that I understand...when you...
View ArticleForum Post: RE: TMS570LS3137: Lockstep verification and intended behavior of...
Hi Marco, I have added my comments after >>. 1) According to the TRM by the CCM self test, the match test, the mismatch test and the error forcing mode check the correct comparison of the signal...
View ArticleForum Post: RE: CCS/MSP430F5359: Calling function inside interrupt
Hello Kary, Rather than calling lengthy functions in ISRs, it's better to do as much as possible in main() to keep the ISRs short and quick. If you're triggering a four second counter in your ISR, I...
View ArticleForum Post: RE: Compiler/MSP430FR2633: Use MSP430FR2633 with arduino
Your easiest bet would be to use the UART to talk to the Arduino over serial. You may need a level translator if you are using a 5 V arduino.
View ArticleForum Post: RE: MSP-EXP430F5529LP: Reading multiple antennas with RFID
Hello Ralph, Thank you for replay. I've written the part of the code so that it suits my needs but it seems I've made a mistake and I can't figure where. I started by switching between two antennas. I...
View ArticleForum Post: RE: MSP432P401R: multiple triggering of DMA completion interrupt...
Since the issue appears to be related to processing within an ISR, I would look for situations where you are preventing the CPU to service an interrupt because it is still in another ISR. Perhaps you...
View ArticleForum Post: RE: MSP-EXP430F5529LP: Reading multiple antennas with RFID
Hello Zan, The issue would be your for loop. You are going through both case statements inside of the for loop, and then exiting the for loop and calling the NFC API's. So you end up in the state of...
View ArticleForum Post: RE: CCS/MSP430FR2633: pragma vector timer routine issue
Matt, I still can't get the timer to work inside of Captivate. It works if I comment out the BSP_configureMCU() and the CAPT_appStart() lines. I have commented out all other instances of BIT0 in...
View ArticleForum Post: RE: MSP432E401Y: HOW TO PORT TM4C129 MCU CODE TO MSP432E401Y
Hello, I cannot suggest or recommend a procedure for that. If possible I would recommend using the TM4C129x device for which the referenced application note was intended. If that is not possible, then...
View ArticleForum Post: RE: MSP432P401R: MSP432 CS_DAP_0 error
thank you for posting the solution. Regards, Chris
View ArticleForum Post: RE: CCS/TMS320F28335: I want to code a closed loop control of...
Raj, I am not sure what is the end application you are trying to do i.e. motor control or solar converters ? We have several references of closed loop motor control which uses spwm, you can refer to...
View ArticleForum Post: RE: TMS320F28051: Wake up requirement from halt different than...
Emil, This is the expected behavior of STANDBY and HALT. HALT requires both the rising and falling edges. STANDBY only requires the falling edge. You will need to figure out another way to determine...
View ArticleForum Post: RE: MSP-EXP430F5529LP: Reading multiple antennas with RFID
Ok but I actually have the rest of the code in that for loop so that shouldn't be a problem, should it be? And even thou, how am I then going to restlessly switch between two antennas (or 20 of them in...
View ArticleForum Post: RE: TMS320F28335: Serial communication not happening unless...
Akhil, Could you please let me know what development tool (if not your own target) you are using? Is it an Experimenter's Kit? - Ken
View ArticleForum Post: RE: TMS320F28235: "function call will not return problem" solved...
Sheldon, Have you made any progress on this topic? Regards, Ozino
View Article